參數資料
型號： S25L004A0LMAI003
廠商： SPANSION LLC
元件分類： PROM
英文描述： 4M X 1 FLASH 3V PROM, PDSO8
封裝： 0.208 INCH, PLASTIC, SOP-8
文件頁數： 24/39頁
文件大小： 945K
代理商： S25L004A0LMAI003
28
S25FL Family (Serial Peripheral Interface) S25FL004A
S25FL004A_00_A1 March 28, 2005
Ad va n c e
In f o rm a t i o n
Figure 17. Release from Deep Power Down and Read Electronic Signature (RES) Instruction Sequence
Power-up and Power-down
The device must not be selected at power-up or power-down (that is, CS# must
follow the voltage applied on VCC) until VCC reaches the correct value as follows:
VCC (min) at power-up, and then for a further delay of tPU (as described in
VSS at power-down
A simple pull-up resistor on Chip Select (CS#) can usually be used to insure safe
and proper power-up and power-down.
The device ignores all instructions until a time delay of tPU (as described in
Table 7, on page 29) has elapsed after the moment that VCC rises above the min-
imum VCC threshold. However, device correct operation is not guaranteed if by
this time VCC is still below VCC (min). No Write Status Register, Program, or Erase
instructions should be sent until tPU after VCC reaches the minimum VCC
threshold.
At power-up, the device is in Standby mode (not Deep Power Down mode) and
the WEL bit is reset.
Normal precautions must be taken for supply rail decoupling to stabilize the
VCC(min) feed. Each device in a system should have the VCC rail decoupled by a
suitable capacitor close to the package pins (this capacitor is generally in the
order of 0.1 F).
At power-down, when VCC drops from the operating voltage to below the VCC(min)
threshold, all operations are disabled and the device does not respond to any in-
structions. (The designer needs to be aware that if a power-down occurs while a
Write, Program, or Erase cycle is in progress, data corruption can result.)
CS#
SCK
SI
SO
3 Dummy
Bytes
High Impedance
MSB
Deep Power Down Mode
Standby Mode
0
1
2
3
4
567
8
9
10
28 29 30 31 32 33 34 35 36 37 38
Electronic ID out
Instruction
tRES
23 22 21
3
2
10
7
654
32
1
0
MSB
相關PDF資料
PDF描述
S25VB80 6 A, 800 V, SILICON, BRIDGE RECTIFIER DIODE
S268P PIN PHOTO DIODE
S29GL01GP12FACR13 1G X 1 FLASH 3V PROM, 120 ns, PBGA64
S29GL128P10TFI010 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology
S29GL128P10TFIR10 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology
相關代理商/技術參數
參數描述
S25M 功能描述:整流器 1000V 25A Std. Recovery RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel
S25M50M3 制造商:SR COMPONENTS 功能描述: 制造商:SR Components Inc 功能描述:
S-25M9F-NM-6' 制造商:Pan Pacific 功能描述:
S-25MD8-10'SI 制造商:Pan Pacific 功能描述:
S-25MF-100' 制造商:Pan Pacific 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*