- 您現在的位置：買賣IC網 > PDF目錄361325 > QT160 (Electronic Theatre Controls, Inc.) 6 KEY CHARGE TRANSFER QTOUCH SENSOR IC PDF資料下載
參數資料
| 型號： | QT160 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 6 KEY CHARGE TRANSFER QTOUCH SENSOR IC |
| 中文描述： | 6鍵電荷轉移一款Qtouch傳感器IC |
| 文件頁數： | 7/12頁 |
| 文件大?。?/td> | 707K |
| 代理商： | QT160 |
3.6 ESD PROTECTION
In cases where the electrode is placed behind a dielectric
panel, the IC will be protected from direct static discharge.
However even with a panel, transients can still flow into the
electrodes via induction, or in extreme cases via dielectric
breakdown. Porous materials may allow a spark to tunnel
right through the material. Testing is required to reveal any
problems. The device does have diode protection on its SNS
pins which absorb and protect the device from most induced
discharges, up to 20mA; the usefulness of the internal
clamping will depending on the dielectric properties, panel
thickness, and rise time of the ESD transients.
In extreme cases ESD dissipation can be aided further with
added series resistors in line with the electrodes as shown in
Figure 1-1. Because the charge time is 1.2 μs, the circuit can
tolerate large values of series-R, up to 20k ohms in cases
where electrode Cx load is below 10pF. Extra diode
protection at the electrodes can also be used, but this often
leads to additional RFI problems as the diodes will rectify RF
signals into DC which will disturb the measurement.
Directly placing semiconductor transient protection devices
or MOV's on the sense leads is not advised; these devices
have extremely large amounts of nonlinear parasitic C which
will swamp the capacitance of the electrode.
Series-R
’
s should be low enough to permit at least 6 RC
time-constants to occur during the charge and transfer
phases, where R is the added series-R and C is the load Cx.
If the device is connected to an external control circuit via a
cable or long twisted pair, it is possible for ground-bounce to
cause damage to the Out pins and/or interfere with key
sensing. Noise current injection into the power supply is best
dealt with by shunting the noise aside to chassis ground with
capacitors, and limited using resistors or ferrites.
3.7 RFI PROTECTION
PCB layout, grounding, and the structure of the input circuitry
have a great bearing on the success of a design that can
withstand strong RF interference.
The circuit is remarkably immune to RFI provided that certain
design rules be adhered to:
1.
U
se SMT components to minimize lead lengths.
2. Always use a ground plane under and around the circuit
and along the sense lines, that is as unbroken as
possible except for relief under and beside the sense
lines to reduce total Cx. Relieved rear ground planes
should be
‘
mended
’
by bridging over them at 1cm
intervals with 0.5mm
‘
rungs
’
like a ladder.
3.
G
round planes should be connected only to a common
point near the Vss pins of the IC.
4. Route sense traces away from other traces or wires that
are connected to other circuits.
5. Sense electrodes should be kept away from other
circuits and grounds which are not directly connected to
the sensor
’
s own circuit ground; other grounds will
appear to float at high frequencies and couple RF
currents into the sense lines.
6. Keep the 6 Cs sampling capacitors and all series-R
components close to the IC.
7.
U
se a 0.1μF minimum ceramic bypass cap very close to
the QT160/161 supply pins.
8.
U
se series-R
’
s in the sense lines, of as large a value as
the circuit can tolerate.
9
. Bypass input power to chassis ground and again at
circuit ground to reduce line-injected noise effects.
Ferrites over the power wiring may be required to
attenuate line injected noise.
Achieving RF immunity mostly requires diligence and a good
working knowledge of grounding, shielding, and layout
techniques.
l
Q
7
QT160/161 1.06/1102
相關PDF資料 |
PDF描述 |
|---|---|
| QT161 | 6 KEY CHARGE TRANSFER QTOUCH SENSOR IC |
| QT301 | CAPACITANCE TO ANALOG CONVERTER |
| QT310 | PROGRAMMABLE CAPACITANCE SENSOR IC |
| QT310-D | PROGRAMMABLE CAPACITANCE SENSOR IC |
| QT310-IS | PROGRAMMABLE CAPACITANCE SENSOR IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| QT1608RL080 | 制造商:MAGIC-TECH 功能描述: |
| QT160-AS | 功能描述:SENSOR IC 6CH 5V 5MA SGL 28-SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:QProx™, QTouch™ 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| QT160-ASG | 功能描述:IC SENSOR 6CH 5V 5MA SGL 28SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:QProx™, QTouch™ 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| QT160-D | 功能描述:SENSOR IC 6-CH 5V 5MA SGL 28-DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:QProx™, QTouch™ 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| QT160-DG | 功能描述:IC SENSOR 6CH 5V 5MA SGL 28DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:QProx™, QTouch™ 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。