參數資料
型號: PSOC
廠商: Cypress Semiconductor Corp.
英文描述: 8-Bit Programmable System-on-Chip (PSoC⑩) Microcontrollers
中文描述: 8位可編程系統(的PSoC⑩)微控制器片上
文件頁數: 47/148頁
文件大?。?/td> 1412K
代理商: PSOC
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁當前第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁
Interrupts
September 5, 2002
Document #: 38-12010 CY Rev. ** CMS Rev. 3.20
47
8.6
GPIO Interrupt
GPIO Interrupts are polarity configurable and pin-wise
maskable (within each Port’s pin configuration registers).
They all share the same interrupt priority and vector.
Any general purpose I/O can be used as an interrupt
source. The GPIO bit in the General Interrupt Mask Reg-
ister (INT_MSK0) must be set to enable pin interrupts, as
well as the enable bits for each pin, which are located in
the Port x Interrupt Enable Registers (PRTxIE). There
are user selectable options to generate an interrupt on 1)
any change from the last read state, 2) rising edge, and
3) falling edge.
When Interrupt on Change is selected, the state of the
GPIO pin is stored when the port is read. Changes from
this state will then assert the interrupt, if enabled.
For a GPIO interrupt to occur, the following steps must
be taken:
1.
The pin Drive Mode must be set so the pin can be
an input.
2.
The pin must be enabled to generate an interrupt by
setting the appropriate bit in the Port interrupt
Enable Register (PRTxIE).
3.
The edge type for the interrupt must be set in the
Port Interrupt Control 0 and Control 1 Registers
(PRTxIC0 and PRTxIC1). Edge type must be set to
a value other than 00.
4.
The GPIO bit must be set in the General Interrupt
Mask Register (INT_MSK0).
5.
The Global Interrupt Enable bit must be set.
6.
Because the GPIO interrupts all share the same
interrupt vector, the source for the GPIO interrupt
must be cleared before any other GPIO interrupt will
occur (i.e., the OR gate in
FigureTitle 11
“ors” all of
the INTOUTn signals together). If any of the
INTOUTn signals are high, the flip-flop in
FigureTitle
11
will not see a rising edge and no IRQ will occur.
Figure 11: GPIO Interrupt Enable Diagram
R
D
IRQ
To Priority
Decode Logic
GPIO Int Enable
BIT S, INT_MSK0
Q
All GPIO INTOUTs
Int Logic
GPIO BIT IE
PORTX IE Register
(PRT0IE...PRT5IE)
INTOUTn
GPIO Cell
PIN
“1”
OR
相關PDF資料
PDF描述
PSOT03LC ULTRA LOW CAPACITANCE TVS ARRAY
PS0T03LC ULTRA LOW CAPACITANCE TVS ARRAY
PSOT05LC ULTRA LOW CAPACITANCE TVS ARRAY
PSOT08LC ULTRA LOW CAPACITANCE TVS ARRAY
PSOT12LC D-SUB
相關代理商/技術參數
參數描述
PSOK10001 制造商:Value Added 功能描述:
PSOODO3A 制造商:MACOM 制造商全稱:Tyco Electronics 功能描述:Versatile Power Entry Module with Small Footprint
PSOODO3B 制造商:MACOM 制造商全稱:Tyco Electronics 功能描述:Versatile Power Entry Module with Small Footprint
PSOODO6A 制造商:MACOM 制造商全稱:Tyco Electronics 功能描述:Versatile Power Entry Module with Small Footprint
PSOODO6B 制造商:MACOM 制造商全稱:Tyco Electronics 功能描述:Versatile Power Entry Module with Small Footprint