- 您現在的位置：買賣IC網 > PDF目錄368151 > PSD403A2-C-70U (意法半導體) TVS BI-DIR 15V 600W DO-15 PDF資料下載
參數資料
| 型號： | PSD403A2-C-70U |
| 廠商： | 意法半導體 |
| 英文描述： | TVS BI-DIR 15V 600W DO-15 |
| 中文描述： | 低成本現場可編程微控制器外圍設備 |
| 文件頁數： | 68/123頁 |
| 文件大小： | 657K |
| 代理商： | PSD403A2-C-70U |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁當前第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁
PSD4XX Famly
65
The PSD4XX
Architecture
(cont.)
Figure 34. Port A In Peripheral I/OMode
RD
PSEL0
PSEL1
D0 – D7
WR
PA0 – PA7
9.4.5 Peripheral I/O
The Peripheral I/O Mode is one of the operating modes of Port A. In this mode, Port A
is connected to the data bus of peripheral devices. Port A is enabled only when
the microcontroller is accessing the devices, otherwise the Port is tri-stated. This feature
enables the microcontroller to access external devices without requiring buffers and
decoders. Figure 34 shows the structure of Port A in the Peripheral I/O Mode.
The memory address space occupied by the devices are defined by two signals: PSEL0
and PSEL1. The signals are direct outputs from the Decoding PLD (DPLD). Whenever any
of the signals is active, the Port A driver is enabled, and the direction of the data flow is
determined by the RD/WR signals.
The Peripheral I/O Mode and the peripheral select signals are configured and defined in the
PSDsoft Software (see the section on I/O Port for configuration). The PIO bit in the VM
Register (see Table 17) also needs to be set to “1” by the user to initialize the Peripheral I/O
Mode.
The Peripheral I/O mode can be used, for example, in DMA applications where the
microcontroller does not support DMA operations, such as tri-stating the address/data bus.
Figure 35 shows a block diagram of a microcontroller and PSD4XX based design that
makes use of this mode. In this application, the microcontroller has a multiplexed bus which
is connected to the ADIO port. The C and D ports connect to the peripheral address bus
and are both configured in Address Out Mode. Port A is configured in the Peripheral I/O
mode and is connected to the peripheral data bus. Ports B and E are used to generate
control signals.
During normal activity, the microcontroller has access to any peripheral (memory or I/O
device) through the PSD4XX device. When there is a DMA request, the
microcontroller tri-states the address bus on Ports C and D by writing a “0” to the port
Direction Registers. The DMA controller then takes over the data and address buses after
receiving acknowledgement from the microcontroller.
相關PDF資料 |
PDF描述 |
|---|---|
| PSD4XX | Low Cost Field Programmable Microcontroller Peripherals |
| PSD401A2-C-15J | IC DDR2 SDRAM 512MB 66-FBGA |
| PSD411A2-C-15J | IC DDR2 SDRAM 512MB 60-TFBGA |
| PSD401A2-C-15L | Low Cost Field Programmable Microcontroller Peripherals |
| PSD411A2-C-15L | IC DDR SDRAM 512MB 66-TSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PSD403A2-C-90JI | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals |
| PSD403A2-C-90UI | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals |
| PSD41 | 制造商:POWERSEM 制造商全稱:POWERSEM 功能描述:Three Phase Rectifier Bridges |
| PSD4-10 | 制造商:Tamura Corporation of America 功能描述: |
| PSD411 | 制造商:PACELEADER 制造商全稱:PACELEADER INDUSTRIAL 功能描述:SURFACE MOUNT SCHOTTKY BARRIER DIODES |
發布緊急采購，3分鐘左右您將得到回復。