- 您現在的位置：買賣IC網 > PDF目錄2097 > MCP3001-I/ST (Microchip Technology)IC ADC 10BIT 2.7V 1CH SPI 8TSSOP PDF資料下載
參數資料
| 型號： | MCP3001-I/ST |
| 廠商： | Microchip Technology |
| 文件頁數： | 9/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 10BIT 2.7V 1CH SPI 8TSSOP |
| 標準包裝： | 100 |
| 位數： | 10 |
| 采樣率（每秒）： | 200k |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 1 |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 8-TSSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個偽差分，單極 |
| 產品目錄頁面： | 672 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
2007 Microchip Technology Inc.
DS21293C-page 17
MCP3001
6.2
Maintaining Minimum Clock Speed
When the MCP3001 initiates the sample period, charge
is stored on the sample capacitor. When the sample
period is complete, the device converts one bit for each
clock that is received. It is important for the user to note
that a slow clock rate will allow charge to bleed off the
sample cap while the conversion is taking place. At
85°C (worst case condition), the part will maintain
proper charge on the sample cap for 700 s at
V
DD = 2.7V and 1.5 ms at VDD = 5V. This means that at
V
DD = 2.7V, the time it takes to transmit the first 14
clocks must not exceed 700 s. Failure to meet this cri-
terion may induce linearity errors into the conversion
outside the rated specifications.
6.3
Buffering/Filtering the Analog Inputs
If the signal source for the ADC is not a low impedance
source, it will have to be buffered or inaccurate conver-
sion results may occur. See Figure 4-2. It is also rec-
ommended that a filter be used to eliminate any signals
that may be aliased back into the conversion results.
This is illustrated in Figure 6-3 where an op amp is
used to drive, filter and gain the analog input of the
MCP3001. This amplifier provides a low impedance
source for the converter input and a low pass filter,
which eliminates unwanted high frequency noise.
Low pass (anti-aliasing) filters can be designed using
Microchip’s interactive FilterLab software. FilterLab
will calculate capacitor and resistor values, as well as
determine the number of poles that are required for the
application. For more information on filtering signals,
see the application note AN699 “Anti-Aliasing Analog
Filters for Data Acquisition Systems.”
FIGURE 6-3:
The MCP601 operational amplifier is
used to implement a 2nd order anti-aliasing filter for
the signal being converted by the MCP3001.
6.4
Layout Considerations
When laying out a printed circuit board for use with
analog components, care should be taken to reduce
noise wherever possible. A bypass capacitor should
always be used with this device and should be placed
as close as possible to the device pin. A bypass capac-
itor value of 1 F is recommended.
Digital and analog traces should be separated as much
as possible on the board and no traces should run
underneath the device or the bypass capacitor. Extra
precautions should be taken to keep traces with high
frequency signals (such as clock lines) as far as possi-
ble from analog traces.
Use of an analog ground plane is recommended in
order to keep the ground potential the same for all
devices on the board. Providing V
DD connections to
devices in a “star” configuration can also reduce noise
by eliminating current return paths and associated
errors. See Figure 6-4. For more information on layout
tips when using ADC, refer to AN-688 “Layout Tips for
12-Bit A/D Converter Applications”.
FIGURE 6-4:
V
DD
traces
arranged
in
a
‘Star’
configuration in order to reduce errors caused by
current return paths.
MCP3001
V
DD
10 F
IN-
IN+
-
+
VIN
C1
C2
V
REF
4.096V
Reference
1F
10 F
0.1 F
MCP601
R1
R2
R3
R4
MCP1541
C
L
V
DD
Connection
Device 1
Device 2
Device 3
Device 4
相關PDF資料 |
PDF描述 |
|---|---|
| MCP3008-I/P | IC ADC 10BIT 2.7V 8CH SPI 16-DIP |
| MCP3021A7T-E/OT | ADC 10BIT I2C INTERFACE SOT23-5 |
| MCP3201T-BI/SN | IC ADC 12BIT 2.7V 1CH SPI 8-SOIC |
| MCP3208T-BI/SL | IC ADC 12BIT 2.7V 8CH SPI 16SOIC |
| MCP3221A5T-E/OT | IC ADC 12BIT 2.7V 1CH LP SOT23-5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP3001T-I/MS | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:2.7V 10 BIT A/D CONVERTER WITH SPI SERIAL INTERFACE |
| MCP3001T-I/P | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:2.7V 10 BIT A/D CONVERTER WITH SPI SERIAL INTERFACE |
| MCP3001T-I/SN | 功能描述:模數轉換器 - ADC 10-bit SPI Sgl Chl IND TEMP, SOIC8 RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MCP3001T-I/ST | 功能描述:模數轉換器 - ADC 10-bit SPI Sgl Chl IND TEMP, TSSOP8 RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MCP3002 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:MCP300X 10-Bit Analog-to-Digital Converters |
發布緊急采購，3分鐘左右您將得到回復。