參數資料
型號： MCZ33990EF
廠商： 飛思卡爾半導體(中國)有限公司
英文描述： Enhanced Class B Serial Transceiver
中文描述： 增強B級串行收發器
文件頁數： 12/16頁
文件大?。?/td> 257K
代理商： MCZ33990EF
Analog Integrated Circuit Device Data
Freescale Semiconductor
12
33990
TYPICAL APPLICATIONS
FUNCTIONAL PIN DESCRIPTION
TYPICAL APPLICATIONS
CLASS B MODULE INPUTS
Transmitter Data from the MCU (TX)
The Tx input is a push-pull (N-channel / P-channel FETs)
buffer with hysteresis for noise immunity purposes. This pin is a
5.0 V CMOS logic level input from the MCU following a true
logic protocol. A logic [0] input drives the BUS
output to 0 V (via
the external pull-down resistor to ground on each node), while
a logic [1] input produces a high voltage at the BUS
output. A
logic [0] input level is guaranteed when the Tx input pin is an
open-circuit by virtue of an internal 40 k
pull-down resistor. No
external resistor is required for its operation.
Waveshaping and 4X / Loop
This input is a tristateable input: 0 V = normal waveshaping,
5.0 V = waveshaping is disabled for 4X transmitting, and high
impedance = loopback mode of operation. This is a logic level
input used to select whether waveshaping for the Class B
output is enabled or disabled. A logic [0] enables waveshaping,
while a logic [1] disables waveshaping. In the 4X mode, the
BUS
output rise time is less than 2.0
μ
s and the fall time is less
than 5.0
μ
s (owing to the external RC pull-down to ground). In
the loopback condition, the Tx signal is fed back to the Rx
output
after
waveshaping
without
being transmitted onto the
BUS. This mode of operation is useful for system diagnostic
purposes.
CLASS B MODULE OUTPUTS
Transceiver Output (BUS)
This is the output driver stage that sources current to the bus.
Its output follows the waveshaped waveform input. Its output
voltage is limited to 6.25 V to 8.0 V under normal battery level
conditions. The limited level is controlled by an internal
regulator/clamp circuit. Once the battery voltage drops below
9.0 V, the regulator / clamp circuit saturates, causing the bus
voltage to track the battery voltage. A 1.5 k
± 5% external
resistor (as well as any 10.6 k
pull-down resistors of any
secondary nodes) sinks the current to discharge the capacitors
during high-to-low transitions. This sourcing output is short
circuit-protected (60 mA to 170 mA) against a short to -2.0 V
and sinks less than 1.0 mA when shorted to V
BAT
. If a short
occurs, the overtemperature shutdown circuit protects the
source driver of the device. In the event battery power is lost to
the assembly, the bus transmitter's output stage will be disabled
and the leakage current from the BUS
output will not source or
sink more than 100 mA of current. The transceiver will operate
with a remote ground offset of ± 2.0 V, but the lower corners of
transmission will
not
be rounded during this condition.
Receiver Output to the Microcontroller (RX)
This is a 5.0 V CMOS compatible push-pull output used to
send received data to the microcontroller. It does not require an
external pull-up resistor to be used. The receiver is always
enabled and draws less than 65
μ
A of current from V
BAT
. The
receive threshold is dependent on the state of the
SLEEP
pin.
The initial state of this output is always a logic [0] after supply
voltage is applied, but before the
SLEEP
pin goes to a logic [1]
state. The receiver circuitry is able to operate with V
BAT
voltages as low as 4.25 V and still remains capable of “waking
up” the 33990 when remote Class B activity is detected.
When the
SLEEP
pin is low and message activity
occurs
on
the bus, the receiver passes the bus
message through to the
microcontroller. The 33990 does not automatically “wake up”
from a sleep state when bus
activity occurs: the microcontroller
must tell it to do so.
In the Static Electrical Characteristics table, the maximum
voltage for Rx is specified as 4.75 V over an operating range of
-40
°
C to 125
°
C temperature and 7.0 V to 16 V V
BAT
. This
maximum Rx voltage is compatible with the minimum V
DD
voltage of microcontrollers to prevent the 33990 from sourcing
current to the microcontroller's output.
Switched Ground Output (LOAD)
Normally this output is a saturated switch to ground, which
pulls down the external resistor between the BUS and LOAD
outputs. In the event ground is lost to the assembly, the LOAD
output will bias itself “off” and will not leak more than 100
μ
A of
current out of this pin.
Overtemperature Shutdown
If the
BUS output becomes shorted to ground for any
duration, an overtemperature shutdown circuit “l(fā)atches off” the
output source transistor whenever the die temperature exceeds
150
°
C to 190
°
C. The output transistor remains latched off until
the Tx input is toggled from a logic [0] to a logic [1]. The rising
edge provides the clearing function, provided the locally sensed
temperature is 10
°
C to 15
°
C below the latch-off temperature trip
temperature.
Waveshaping
Waveshaping is incorporated into the 33990 to minimize
radiated EMI emissions.
Receiver Protocol
The Class B communication scheme uses a variable pulse
width (VPW) protocol. The microcontroller provides the VPW
decoding function. Once the receiver detects a transition on Rx,
it starts an internal counter. The initial “start of frame” bit is a
logic [1] and lasts 200
μ
s. For subsequent bits, if there is a bus
相關PDF資料
PDF描述
MCZ33991EG Gauge Driver Integrated Circuit
MCZ33993EW Multiple Switch Detection Interface
MCZ33996EK 16-Output Switch with SPI Control
MCZ34652EF 2.0 A Negative Voltage Hot Swap Controller with Enhanced Programmability
MCZ34701EWR2 1.5A Switch-Mode Power Supply with Linear Regulator
相關代理商/技術參數
參數描述
MCZ33990EF 制造商:Freescale Semiconductor 功能描述:TRANCEIVER J-1850 CLASS B 8SOIC
MCZ33990EF/R2 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Enhanced Class B Serial Transceiver
MCZ33990EFR2 功能描述:網絡控制器與處理器 IC CLASS B SERIAL TRANS RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MCZ33991EG 功能描述:馬達/運動/點火控制器和驅動器 GAUGE DRIVER IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MCZ33991EGR2 功能描述:馬達/運動/點火控制器和驅動器 GAUGE DRIVER IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*