- 您現在的位置：買賣IC網 > PDF目錄379307 > MC14555BF (ON SEMICONDUCTOR) Dual Binary to 1-of-4 Decoder/Demultiplexer PDF資料下載
參數資料
| 型號： | MC14555BF |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 通用總線功能 |
| 英文描述： | Dual Binary to 1-of-4 Decoder/Demultiplexer |
| 中文描述： | 4000/14000/40000 SERIES, OTHER DECODER/DRIVER, TRUE OUTPUT, PDSO16 |
| 封裝： | PLASTIC, EIAJ, SOIC-16 |
| 文件頁數： | 4/20頁 |
| 文件大?。?/td> | 342K |
| 代理商： | MC14555BF |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
MC145554
MC145557
MC145564
MC145567
4
MOTOROLA
serial PCM word, clocked by BCLKX, out of DX. If the FSX
pulse is high for more than eight BCLKX periods, the DX and
TSX outputs will remain in a low–impedance state until FSX
is brought low. The length of the FSX pulse is used to deter-
mine whether the transmit and receive digital I/O conforms to
the Short Frame Sync or to the Long Frame Sync conven-
tion.
TSX
Transmit Time Slot Indicator
This is an open–drain output that goes low whenever the
DX output is in a low–impedance state (i.e., during the trans-
mit time slot when the PCM word is being output) for en-
abling a PCM bus driver.
ANLB
Analog Loopback Control Input (MC145564/67 Only)
When held high, this pin causes the input of the transmit
RC active filter to be disconnected from GSX and connected
to VPO+ for analog loopback testing. This pin is held low in
normal operation.
ANALOG
GSX
Gain–Setting Transmit
This output of the transmit gain–adjust operational amplifi-
er is internally connected to the encoder section of the
device. It must be used in conjunction with VFXI– and VFXI+
to set the transmit gain for a maximum signal amplitude of
2.5 V peak. This output can drive a 600
load to 2.5 V peak.
VFXI–
Voice–Frequency Transmit Input (Inverting)
This is the inverting input of the transmit gain–adjust
operational amplifier.
VFXI+
Voice–Frequency Transmit Input
(Non–Inverting)
This is the non–inverting input of the transmit gain–adjust
operational amplifier.
VFRO
Voice–Frequency Receive Output
This receive analog output is capable of driving a 600
load to 2.5 V peak.
VPI
Voltage Power Input (MC145564/67 Only)
This is the inverting input to the first receive power ampli-
fier. Both of the receive power amplifiers can be powered
down by connecting this input to VBB.
VPO–
Voltage Power Output (Inverted) (MC145564/67 Only)
This inverted output of the receive push–pull power ampli-
fiers can drive 300
to 3.3 V peak.
VPO+
Voltage Power Output (Non–Inverted)
(MC145554/67 Only)
This non–inverted output of the receive push–pull power
amplifier pair can drive 300
to 3.3 V peak.
POWER SUPPLY
GNDA
Analog Ground
This terminal is the reference level for all signals, both ana-
log and digital. It is 0 V.
VCC
Positive Power Supply
VCC is typically 5 V.
VBB
Negative Power Supply
VBB is typically – 5 V.
FUNCTIONAL DESCRIPTION
ANALOG INTERFACE AND SIGNAL PATH
The transmit portion of these codec–filters includes a low–
noise gain setting amplifier capable of driving a 600
load.
Its output is fed to a three–pole anti–aliasing pre–filter. This
pre–filter incorporates a two–pole Butterworth active low–
pass filter, and a single passive pole. This pre–filter is fol-
lowed by a single ended–to–differential converter that is
clocked at 256 kHz. All subsequent analog processing uti-
lizes fully differential circuitry. The next section is a fully–dif-
ferential, five–pole switched capacitor low–pass filter with a
3.4 kHz passband. After this filter is a 3–pole switched–ca-
pacitor high–pass filter having a cutoff frequency of about
200 Hz. This high–pass stage has a transmission zero at dc
that eliminates any dc coming from the analog input or from
accumulated operational amplifier offsets in the preceding fil-
ter stages. The last stage of the high–pass filter is an auto-
zeroed sample and hold amplifier.
One bandgap voltage reference generator and digital–to–
analog converter (DAC) are shared by the transmit and
receive sections. The autozeroed, switched–capacitor band-
gap reference generates precise positive and negative refer-
ence voltages that are independent of temperature and
power supply voltage. A binary–weighted capacitor array
(CDAC) forms the chords of the companding structure, while
a resistor string (RDAC) implements the linear steps within
each chord. The encode process uses the DAC, the voltage
reference, and a frame–by–frame autozeroed comparator to
implement a successive–approximation conversion algo-
rithm. All of the analog circuitry involved in the data con-
version — the voltage reference, RDAC, CDAC, and
comparator — are implemented with a differential architec-
ture.
The receive section includes the DAC described above, a
sample and hold amplifier, a five–pole 3400 Hz switched
capacitor low–pass filter with sinX/X correction, and a two–
pole active smoothing filter to reduce the spectral com-
ponents of the switched capacitor filter. The output of the
smoothing filter is a power amplifier that is capable of driving
a 600
load. The MC145564 and MC145567 add a pair of
power amplifiers that are connected in a push–pull configu-
ration; two external resistors set the gain of both of the
相關PDF資料 |
PDF描述 |
|---|---|
| MC14555BFEL | Dual Binary to 1-of-4 Decoder/Demultiplexer |
| MC14555 | PCM Codec-Filter |
| MC145557P | PCM Codec-Filter |
| MC145557 | PCM Codec-Filter |
| MC145564 | PCM Codec-Filter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC14555BFEL | 功能描述:編碼器、解碼器、復用器和解復用器 3-18V Dual Binary to RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量（輸入/輸出）:2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray |
| MC14555BFELG | 功能描述:編碼器、解碼器、復用器和解復用器 LOG CMOS DCODE/ DMULTI 1-4 RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量（輸入/輸出）:2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray |
| MC14555BFL1 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MC145564P | 制造商:Motorola Inc 功能描述: |
| MC14556BCP | 功能描述:編碼器、解碼器、復用器和解復用器 LOG CMOS DCODE/ DMULTI 1-4 RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量（輸入/輸出）:2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。