- 您現在的位置：買賣IC網 > PDF目錄379305 > MC14522BCP (MOTOROLA INC) Presettable 4-Bit Down Counters PDF資料下載
參數資料
| 型號： | MC14522BCP |
| 廠商： | MOTOROLA INC |
| 元件分類： | 通用總線功能 |
| 英文描述： | Presettable 4-Bit Down Counters |
| 中文描述： | 4000/14000/40000 SERIES, SYN POSITIVE EDGE TRIGGERED 4-BIT DOWN DECADE COUNTER, PDIP16 |
| 封裝： | PLASTIC, DIP-16 |
| 文件頁數： | 8/10頁 |
| 文件大小： | 272K |
| 代理商： | MC14522BCP |
MOTOROLA CMOS LOGIC DATA
MC14522B MC14526B
8
APPLICATIONS INFORMATION
Divide–By–N, Single Stage
Figure 11 shows a single stage divide–by–N application.
The MC14522B (BCD version) can accept a number greater
than 9 and count down in binary fashion. Hence, the BCD
and binary single stage divide–by–N counters (as shown in
Figure 11) function the same.
To initialize counting a number, N is set on the parallel in-
puts (P0, P1, P2, and P3) and reset is taken high asynchro-
nously. A zero is forced into the master and slave of each bit
and, at the same time, the “0” output goes high. Because
Preset Enable is tied to the “0” output, preset is enabled. Re-
set must be released while the Clock is high so the slaves of
each bit may receive N before the Clock goes low. When the
Clock goes low and Reset is low, the “0” output goes low (if
P0 through P3 are unequal to zero).
The counter downcounts with each rising edge of the
Clock. When the counter reaches the zero state, an output
pulse occurs on “0” which presets N. The propagation delays
from the Clock’s rising and falling edges to the “0” output’s
rising and falling edges are about equal, making the “0” out-
put pulse approximately equal to that of the Clock pulse.
The Inhibit pin may be used to stop pulse counting. When
this pin is taken high, decrementing is inhibited.
Cascaded, Presettable Divide–By–N
Figure 12 shows a three stage cascade application. Taking
Reset high loads N. Only the first stage’s Reset pin (least sig-
nificant counter) must be taken high to cause the preset for
all stages, but all pins could be tied together, as shown.
When the first stage’s Reset pin goes high, the “0” output is
latched in a high state. Reset must be released while Clock is
high and time allowed for Preset Enable to load N into all
stages before Clock goes low.
When Preset Enable is high and Clock is low, time must be
allowed for the zero digits to propagate a Cascade Feedback
to the first non–zero stage. Worst case is from the most sig-
nificant bit (M.S.B.) to the L.S.B., when the L.S.B. is equal to
one (i.e. N = 1).
After N is loaded, each stage counts down to zero with
each rising edge of Clock. When any stage reaches zero and
the leading stages (more significant bits) are zero, the “0”
output goes high and feeds back to the preceding stage.
When all stages are zero, the Preset Enable automatically
loads N while the Clock is high and the cycle is renewed.
Figure 11.
÷
N Counter
P0
P1
P2
P3
CF
RESET
INHIBIT
CLOCK
PE
Q0
Q1
Q2
Q3
“0”
N
VDD
VSS
fin
BUFFER
fin
N
Figure 12. 3 Stages Cascaded
N0 N1 N2 N3
N4 N5 N6 N7
P0 P1 P2 P3
CLOCK
Q0 Q1Q2 Q3
fin
INHIBIT
RESET
VSS
VDD
LOAD
N
VSS
“0”
PE
CF
10 K
VSS
P0 P1 P2 P3
CLOCK
Q0 Q1Q2 Q3
INHIBIT
RESET
“0”
PE
CF
CLOCK
INHIBIT
RESET
“0”
PE
CF
P0 P1 P2 P3
Q0 Q1Q2 Q3
N8 N9N10 N11
VSS
VDD
BUFFER
LSB
MSB
fin
N
相關PDF資料 |
PDF描述 |
|---|---|
| MC14522BDW | Presettable 4-Bit Down Counters |
| MC14527BCL | BCD Rate Multiplier |
| MC14527BCP | Inverting Fast Synchronous Buck MOSFET Drivers with Enable 14-HTSSOP |
| MC14527BDW | BCD Rate Multiplier |
| MC14534BCL | Inverting Fast Synchronous-Buck MOSFET Driver with Internal Adjustable Regulator 16-HTSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC14522BDW | 制造商:Motorola Inc 功能描述: |
| MC14526B AC7 WAF | 制造商:ON Semiconductor 功能描述: |
| MC14526BAC7 WAF | 制造商:ON Semiconductor 功能描述: |
| MC14526BCL | 制造商: 功能描述: 制造商:undefined 功能描述: |
| MC14526BCP | 功能描述:計數器移位寄存器 3-18V Presettable RoHS:否 制造商:Texas Instruments 計數器類型: 計數順序:Serial to Serial/Parallel 電路數量:1 封裝 / 箱體:SOIC-20 Wide 邏輯系列: 邏輯類型: 輸入線路數量:1 輸出類型:Open Drain 傳播延遲時間:650 ns 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。