參數資料
型號: MC145027DW
廠商: MOTOROLA INC
元件分類: 搖控器
英文描述: Encoder and Decoder Pairs
中文描述: RECEIVER IC, PDSO16
封裝: SOG-16
文件頁數: 16/20頁
文件大?。?/td> 233K
代理商: MC145027DW
MC145026
MC145027
MC145028
SC41343
SC41344
16
MOTOROLA
APPLICATIONS INFORMATION
INFRARED TRANSMITTER
In Figure 18, the MC145026 encoder is set to run at an os-
cillator frequency of about 4 to 9 kHz. Thus, the time required
for a complete two–word encoding sequence is about 20 to
40 ms. The data output from the encoder gates an RC oscilla-
tor running at 50 kHz; the oscillator shown starts rapidly
enough to be used in this application. When the “send” button
is not depressed, both the MC145026 and oscillator are in a
low–power standby state. The RC oscillator has to be
trimmed for 50 kHz and has some drawbacks for frequency
stability. A superior system uses a ceramic resonator oscilla-
tor running at 400 kHz. This oscillator feeds a divider as
shown in Figure 19. The unused inputs of the MC14011UB
must be grounded.
The MLED81 IRED is driven with the 50 kHz square wave
at about 200 to 300 mA to generate the carrier. If desired, two
IREDs wired in series can be used (see Application Note
AN1016 for more information). The bipolar IRED switch,
shown in Figure 18, offers two advantages over a FET. First,
a logic FET has too much gate capacitance for the
MC14011UB to drive without waveform distortion. Second,
the bipolar drive permits lower supply voltages, which are an
advantage in portable battery–powered applications.
The configuration shown in Figure 18 operates over a
supply range of 4.5 to 18 V. A low–voltage system which
operates down to 2.5 V could be realized if the oscillator sec-
tion of a MC74HC4060 is used in place of the MC14011UB.
The data output of the MC145026 is inverted and fed to the
RESET pin of the MC74HC4060. Alternately, the
MC74HCU04 could be used for the oscillator.
Information on the MC14011UB is in book number
DL131/D. The MC74HCU04 and MC74HC4060 are found in
book number DL129/D.
INFRARED RECEIVER
The receiver in Figure 20 couples an IR–sensitive diode to
input preamp A1, followed by band–pass amplifier A2 with a
gain of about 10. Limiting stage A3 follows, with an output of
about 800 mV p–p. The limited 50 kHz burst is detected by
comparator A4 that passes only positive pulses, and peak–
detected and filtered by a diode/RC network to extract the
data envelope from the burst. Comparator A5 boosts the sig-
nal to logic levels compatible with the MC145027/28 data
input. The Din pin of these decoders is a standard CMOS
high–impedance input which must
not
be allowed to float.
Therefore, direct coupling from A5 to the decoder input is
utilized.
Shielding should be used on at least A1 and A2, with good
ground and high–sensitivity circuit layout techniques applied.
For operation with supplies higher than + 5 V, limiter A4’s
positive output swing needs to be limited to 3 to 5 V. This is
accomplished via adding a zener diode in the negative feed-
back path, thus avoiding excessive system noise. The bias-
ing resistor stack should be adjusted such that V3 is 1.25 to
1.5 V.
This system works up to a range of about 10 meters. The
gains of the system may be adjusted to suit the individual
design needs. The 100
resistor in the emitter of the first
2N5088 and the 1 k
resistor feeding A2 may be altered if
different gain is required. In general, more gain does not nec-
essarily result in increased range. This is due to noise floor
limitations. The designer should increase transmitter power
and/or increase receiver aperature with Fresnal lensing to
greatly improve range. See Application Note AN1016 for
additional information.
Information on the MC34074 is in data book DL128/D.
TRINARY SWITCH MANUFACTURERS
Midland Ross–Electronic Connector Div.
Greyhill
Augat/Alcoswitch
Aries Electronics
The above companies may not have the switches in a DIP.
For more information, call them or consult eem Electronic En-
gineers Master Catalogor the Gold Book
Ask for SPDT with
center OFF
.
Alternative: An SPST can be placed in series between a
SPDT and the Encoder or Decoder to achieve trinary action.
Motorola cannot recommend one supplier over another
and in no way suggests that this is a complete listing of trinary
switch manufacturers.
相關PDF資料
PDF描述
MC145027P Encoder and Decoder Pairs
MC145028 High Power Wide Voltage Range Quad Port Ethernet Power Sourcing Equipment Manager 64-HTQFP -40 to 125
MC145028DW Encoder and Decoder Pairs
MC145028P Encoder and Decoder Pairs
MC14502BCL Strobed Hex Inverter/Buffer
相關代理商/技術參數
參數描述
MC145027DWR2 功能描述:IC DECODER 5 ADDR 4 DATA 16-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 編碼器,解碼器,轉換器 系列:4000 產品變化通告:Development Systems Discontinuation 26/Apr/2011 標準包裝:1 系列:- 類型:編碼器 應用:DVB-S.2 系統 電壓 - 電源,模擬:- 電壓 - 電源,數字:- 安裝類型:- 封裝/外殼:模塊 供應商設備封裝:模塊 包裝:散裝 其它名稱:Q4645799
MC145027P 功能描述:IC DECODER 5 ADDR 4 DATA 16-DIP RoHS:否 類別:集成電路 (IC) >> 接口 - 編碼器,解碼器,轉換器 系列:4000 產品變化通告:Development Systems Discontinuation 26/Apr/2011 標準包裝:1 系列:- 類型:編碼器 應用:DVB-S.2 系統 電壓 - 電源,模擬:- 電壓 - 電源,數字:- 安裝類型:- 封裝/外殼:模塊 供應商設備封裝:模塊 包裝:散裝 其它名稱:Q4645799
MC145028DW 功能描述:鎖相環 - PLL Decoder RoHS:否 制造商:Silicon Labs 類型:PLL Clock Multiplier 電路數量:1 最大輸入頻率:710 MHz 最小輸入頻率:0.002 MHz 輸出頻率范圍:0.002 MHz to 808 MHz 電源電壓-最大:3.63 V 電源電壓-最小:1.71 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:QFN-36 封裝:Tray
MC145028DWR2 功能描述:IC DECODER 9 ADDR 16-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 編碼器,解碼器,轉換器 系列:4000 產品變化通告:Development Systems Discontinuation 26/Apr/2011 標準包裝:1 系列:- 類型:編碼器 應用:DVB-S.2 系統 電壓 - 電源,模擬:- 電壓 - 電源,數字:- 安裝類型:- 封裝/外殼:模塊 供應商設備封裝:模塊 包裝:散裝 其它名稱:Q4645799
MC145028P 功能描述:IC DECODER 9 ADDR LINES 16-DIP RoHS:否 類別:集成電路 (IC) >> 接口 - 編碼器,解碼器,轉換器 系列:4000 產品變化通告:Development Systems Discontinuation 26/Apr/2011 標準包裝:1 系列:- 類型:編碼器 應用:DVB-S.2 系統 電壓 - 電源,模擬:- 電壓 - 電源,數字:- 安裝類型:- 封裝/外殼:模塊 供應商設備封裝:模塊 包裝:散裝 其它名稱:Q4645799