- 您現在的位置：買賣IC網 > PDF目錄383492 > MAX810JTR (Maxim Integrated Products, Inc.) Analog IC PDF資料下載
參數資料
| 型號： | MAX810JTR |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Analog IC |
| 中文描述： | 模擬IC |
| 文件頁數： | 5/11頁 |
| 文件大?。?/td> | 218K |
| 代理商： | MAX810JTR |
M
Low-Cost, μP Supervisory Circuits
_______________________________________________________________________________________
5
______________________________________________________________Pin Description
PIN
MAX813L
Watchdog Output pulls low when the internal watch-
dog timer finishes its 1.6sec count and does not go
high again until the watchdog is cleared. WDO also
goes low during low-line conditions. Whenever V
CC
is
below the reset threshold, WDO stays low; however,
unlike RESET, WDO does not have a minimum pulse
width. As soon as V
CC
rises above the reset thresh-
old, WDO goes high with no delay.
Active-High Reset Output is the inverse of RESET.
Whenever RESET is high, RESET is low, and vice
versa (Figure 2). The MAX813L has a RESET output
only.
Active-Low Reset Output pulses low for 200ms when
triggered, and stays low whenever V
CC
is below the
reset threshold (4.65V in the MAX705 and 4.40V in the
MAX706). It remains low for 200ms after V
CC
rises
above the reset threshold or MR goes from low to high
(Figure 3). A watchdog timeout will not trigger RESET
unless WDO is connected to MR.
Watchdog Input. If WDI remains high or low for
1.6sec, the internal watchdog timer runs out and
WDO goes low (Figure 1). Floating WDI or connect-
ing WDI to a high-impedance three-state buffer dis-
ables the watchdog feature. The internal watchdog
timer clears whenever reset is asserted, WDI is three-
stated, or WDI sees a rising or falling edge.
Power-Fail Output goes low and sinks current when
PFI is less than 1.25V; otherwise PFO stays high.
Power-Fail Voltage Monitor Input. When PFI is less
than 1.25V, PFO goes low. Connect PFI to GND or
V
CC
when not used.
FUNCTION
MAX705/MAX706
DIP/SO
RESET
7
8
-
WDO
8
-
8
RESET
-
7
7
No Connect
N.C.
-
6
-
WDI
6
-
6
PFO
5
5
5
PFI
4
4
4
0V Ground Reference for all signals
GND
3
3
3
+5V Supply Input
V
CC
2
2
2
NAME
DIP/SO
DIP/SO
MAX707/MAX708
-
2
1
-
8
7
6
5
4
μMAX
2
-
1
-
-
7
6
5
4
μMAX
1
2
-
-
8
7
6
5
4
μMAX
Manual-Reset Input triggers a reset pulse when
pulled below 0.8V. This active-low input has an inter-
nal 250μA pull-up current. It can be driven from a TTL
or CMOS logic line as well as shorted to ground with
a switch.
MR
1
1
1
3
3
3
相關PDF資料 |
PDF描述 |
|---|---|
| MAX811CUS-T | Analog IC |
| MAX811LCUS-T | Voltage Detector |
| MAX811LEUS-T | Voltage Detector |
| MAX811MCUS-T | Voltage Detector |
| MAX811MEUS-T | Voltage Detector |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX810JW | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:3-pin microprocessor resets |
| MAX810L | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:3-pin microprocessor resets |
| MAX810LCPA | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Voltage Detector |
| MAX810LCUR | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Voltage Detector |
| MAX810LD | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:3-pin microprocessor resets |
發布緊急采購，3分鐘左右您將得到回復。