- 您現在的位置：買賣IC網 > PDF目錄65805 > MAX6822WUK+T (MAXIM INTEGRATED PRODUCTS INC) Low-Voltage SOT23 µP Supervisors with Manual Reset and Watchdog Timer PDF資料下載
參數資料
| 型號： | MAX6822WUK+T |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | Low-Voltage SOT23 µP Supervisors with Manual Reset and Watchdog Timer |
| 中文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO5 |
| 封裝： | LEAD FREE, SOT-23, 5 PIN |
| 文件頁數： | 5/9頁 |
| 文件大?。?/td> | 355K |
| 代理商： | MAX6822WUK+T |
MAX6821–MAX6825
Low-Voltage SOT23 P Supervisors with
Manual Reset and Watchdog Timer
_______________________________________________________________________________________
5
Pin Description
PIN NUMBERS
MAX6821 MAX6822 MAX6823 MAX6824 MAX6825
PIN
NAME
FUNCTION
1
RESET
Active-Low Open-Drain or Push-Pull Reset Output. RESET
changes from high to low when the VCC input drops below the
selected reset threshold, MR is pulled low, or the watchdog
triggers a reset. RESET remains low for the reset timeout period
after VCC exceeds the device reset threshold, MR goes low to
high, or the watchdog triggers a reset.
1
3
RESET
Active-High Push-Pull Reset Output. RESET changes from low to
high when the VCC input drops below the selected reset threshold,
MR is pulled low, or the watchdog triggers a reset. RESET remains
high for the reset timeout period after VCC exceeds the device
reset threshold, MR goes low to high, or the watchdog triggers a
reset.
2
GND
Ground
3
4
MR
Active-Low Manual Reset Input. Internal 50k
pullup to VCC. Pull
low to force a reset. Reset remains active as long as MR is low
and for the reset timeout period after MR goes high. Leave
unconnected or connect to VCC if unused.
4
WDI
Watchdog Input. If WDI remains high or low for longer than the
watchdog timeout period, the internal watchdog timer runs out and
a reset is triggered for the reset timeout period. The internal
watchdog timer clears whenever reset is asserted, the manual
reset is asserted, or WDI sees a rising or falling edge. If WDI is
left unconnected or is connected to a three-stated buffer output,
the watchdog feature is disabled.
5
VCC
Supply Voltage and Input for Reset Threshold Monitor
Detailed Description
RESET/RESET Output
A P’s reset input starts the P in a known state. The
MAX6821–MAX6825 P supervisory circuits assert a
reset to prevent code-execution errors during power-
up, power-down, and brownout conditions. Whenever
VCC falls below the reset threshold, the reset output
asserts low for RESET and high for RESET. Once VCC
exceeds the reset threshold, an internal timer keeps the
reset output asserted for the specified reset timeout
period (tRP); after this interval, reset output returns to its
original state (see Figure 2).
Manual Reset Input
Many P-based products require manual reset capabil-
ity, allowing the operator, a test technician, or external
logic circuitry to initiate a reset. On the MAX6821/
MAX6822/MAX6823/MAX6825, a logic low on MR
asserts a reset. Reset remains asserted while MR is
low, and for the timeout period (140ms min) after it
returns high. MR has an internal 50k
pullup resistor,
so it can be left open if not used. This input can be dri-
ven with CMOS logic levels or with open-drain/collector
outputs. Connect a normally open momentary switch
from MR to GND to create a manual reset function;
external debounce circuitry is not required. If MR is dri-
ven from long cables or the device is used in a noisy
environment, connect a 0.1F capacitor from MR to
GND to provide additional noise immunity.
Watchdog Input
In the MAX6821–MAX6824, the watchdog circuit moni-
tors the P’s activity. If the P does not toggle (low to
high or high to low) the watchdog input (WDI) within the
watchdog timeout period (1.6s nominal), reset asserts
for the reset timoeout period. The internal 1.6s timer
can be cleared by either a reset pulse or by toggling
WDI. The WDI can detect pulses as short as 50ns.
While reset is asserted, the timer remains cleared and
does not count. As soon as reset is released, the timer
starts counting (see Figure 3).
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6822ZUK+T | Low-Voltage SOT23 µP Supervisors with Manual Reset and Watchdog Timer |
| MAX6823LUK+T | Low-Voltage SOT23 µP Supervisors with Manual Reset and Watchdog Timer |
| MAX6823MUK+T | Low-Voltage SOT23 µP Supervisors with Manual Reset and Watchdog Timer |
| MAX6823RUK+T | Low-Voltage SOT23 µP Supervisors with Manual Reset and Watchdog Timer |
| MAX6823SUK+T | Low-Voltage SOT23 µP Supervisors with Manual Reset and Watchdog Timer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6822YUK | 制造商:Maxim Integrated Products 功能描述:LOW-VOLTAGE SOT23 MICROPROCESSOR SU - Cut Tape Product |
| MAX6822YUK+ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX6822YUK+T | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6822YUK-T | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6822ZUK | 制造商:Maxim Integrated Products 功能描述:LOW-VOLTAGE SOT23 MICROPROCESSOR SU - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。