- 您現在的位置：買賣IC網 > PDF目錄383292 > M25P40-VMP6TP (意法半導體) 4 Mbit Uniform Sector, Serial Flash Memory PDF資料下載
參數資料
| 型號： | M25P40-VMP6TP |
| 廠商： | 意法半導體 |
| 元件分類： | DRAM |
| 英文描述： | 4 Mbit Uniform Sector, Serial Flash Memory |
| 中文描述： | 4兆位統一部門，串行閃存 |
| 文件頁數： | 21/40頁 |
| 文件大小： | 232K |
| 代理商： | M25P40-VMP6TP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
21/40
M25P40
Sector Erase (SE)
The Sector Erase (SE) instruction sets to 1 (FFh)
all bits inside the chosen sector. Before it can be
accepted, a Write Enable (WREN) instruction
must previously have been executed. After the
Write Enable (WREN) instruction has been decod-
ed, the device sets the Write Enable Latch (WEL).
The Sector Erase (SE) instruction is entered by
driving Chip Select (S) Low, followed by the in-
struction code, and three address bytes on Serial
Data Input (D). Any address inside the Sector (see
Table 3.
) is a valid address for the Sector Erase
(SE) instruction. Chip Select (S) must be driven
Low for the entire duration of the sequence.
The instruction sequence is shown in
Figure 15.
.
Chip Select (S) must be driven High after the
eighth bit of the last address byte has been latched
in, otherwise the Sector Erase (SE) instruction is
not executed. As soon as Chip Select (S) is driven
High, the self-timed Sector Erase cycle (whose du-
ration is t
SE
) is initiated. While the Sector Erase cy-
cle is in progress, the Status Register may be read
to check the value of the Write In Progress (WIP)
bit. The Write In Progress (WIP) bit is 1 during the
self-timed Sector Erase cycle, and is 0 when it is
completed. At some unspecified time before the
cycle is completed, the Write Enable Latch (WEL)
bit is reset.
A Sector Erase (SE) instruction applied to a page
which is protected by the Block Protect (BP2, BP1,
BP0) bits (see
Table 3.
and
Table 2.
) is not execut-
ed.
Figure 15. Sector Erase (SE)
Instruction Sequence
Note: 1. Address bits A23 to A19 are Don’t Care.
24 Bit Address
C
D
AI03751D
S
2
1
3
4
5
6
7
8
9
29 30 31
Instruction
0
23 22
2
0
1
MSB
相關PDF資料 |
PDF描述 |
|---|---|
| M25SI | Thin Film, Rectangular, Fusible, Resistor Chips |
| M27256-F1 | NMOS 256K 32K x 8 UV EPROM |
| M27256-F6 | NMOS 256K 32K x 8 UV EPROM |
| M2732A-20F1 | NMOS 32K 4K x 8 UV EPROM |
| M2732A-20F6 | NMOS 32K 4K x 8 UV EPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M25P40-VMP6TP/X | 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:4 Mbit, low voltage, serial Flash memory with 50 MHz SPI bus interface |
| M25P40-VMP6Txx | 制造商:MICRON 制造商全稱:Micron Technology 功能描述:Micron M25P40 Serial Flash Embedded Memory |
| M25P40-VMS6GB | 制造商:Micron Technology Inc 功能描述:SERIAL NOR - Trays |
| M25P40-VMS6Gx | 制造商:MICRON 制造商全稱:Micron Technology 功能描述:Micron M25P40 Serial Flash Embedded Memory |
| M25P40-VMS6TGB | 制造商:Micron Technology Inc 功能描述:SERIAL NOR - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。