- 您現在的位置：買賣IC網 > PDF目錄65797 > LV8098CS (SANYO SEMICONDUCTOR CO LTD) VOICE COIL MOTOR CONTROLLER, 0.1 A, PBGA6 PDF資料下載
參數資料
| 型號： | LV8098CS |
| 廠商： | SANYO SEMICONDUCTOR CO LTD |
| 元件分類： | 運動控制電子 |
| 英文描述： | VOICE COIL MOTOR CONTROLLER, 0.1 A, PBGA6 |
| 封裝： | 1.27 X 0.87 MM, 0.50 MM HEIGHT, WLP-6 |
| 文件頁數： | 7/8頁 |
| 文件大?。?/td> | 222K |
| 代理商： | LV8098CS |
LV8098CS
No.A1515-7/8
The standard data transfer to this device consists of three bytes : the slave address of the first byte and the data of the
second and third bytes.
Slave address : 0110011(0)
PD : Power-down
D1-D7 : 8-bit data used to set output constant current ; MIN = 00000000, MAX = 11111111
The table below shows the format of the second and third bytes.
2nd byte
3rd byte
Serial data bits
SD7
SD6
SD5
SD4
SD3
SD2
SD1
SD0
SD7
SD6
SD5
SD4
SD3
SD2
SD1
SD0
Function
PD
×
D7
D6
D5
D4
D3
D2
D1
D0
×
PD bit setting method
PD = 1
→ Power_down (standby mode) and reset
D0-D7 setting method
Current setting code
D7
D6
D5
D4
D3
D2
D1
Output setting
(LSB)
Output current (mA)
(design value)
0
1
0
1
0.392
2
0
1
0
2
0.784
254
1
0
254
99.608
255
1
255
100
Relationship between the ENA pin input, I
2C input data PD, and current setting 0 (code 0)
This IC supports the following three modes of setting up the standby mode :
1) Setting the ENA pin low.
2) Setting the PD bit to 1 (high) with I
2C input data.
3) Setting the output current to 0 with I
2C input data.
Execution of one of the steps 1) to 3) causes the output current to 0 and stops operation of the circuit.
When the ENA pin is set low, the I
2C data register is reset and the IC is reset to its default state (PD bit set to 0 and output
current setting to code 0).
Since the IC starts operation in the data reset state at power-on time, it is necessary to start using the IC in the default state
by setting the ENA pin low before turning on VCC and then high after VCC is established.
相關PDF資料 |
PDF描述 |
|---|---|
| LV8098CS | VOICE COIL MOTOR CONTROLLER, 0.1 A, PBGA6 |
| LV8406T | BRUSH DC MOTOR CONTROLLER, 2.5 A, PDSO20 |
| LV8413GP | BRUSH DC MOTOR CONTROLLER, 0.6 A, QCC16 |
| LV8413GP | BRUSH DC MOTOR CONTROLLER, QCC16 |
| LV8804FV | AC MOTOR CONTROLLER, 1.2 A, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LV8099CS | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Constant-current Driver IC |
| LV8099CS-TE-L-H | 制造商:ON Semiconductor 功能描述:VOICE COIL MOTOR DRIVER - Tape and Reel 制造商:Rochester Electronics LLC 功能描述: 制造商:ON Semiconductor 功能描述:REEL / VOICE COIL MOTOR DRIVER 制造商:Sony Semiconductor Solutions Division 功能描述: |
| LV8099CT | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:For VCMs Constant-current Driver IC |
| LV8099CT-TE-L-H | 功能描述:IC MOTOR DRIVER S111 WLP RoHS:是 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 外部開關 系列:* 標準包裝:5 系列:- 配置:低端 輸入類型:非反相 延遲時間:600ns 電流 - 峰:12A 配置數:1 輸出數:1 高端電壓 - 最大（自引導啟動）:- 電源電壓:14.2 V ~ 15.8 V 工作溫度:-20°C ~ 60°C 安裝類型:通孔 封裝/外殼:21-SIP 模塊 供應商設備封裝:模塊 包裝:散裝 配用:BG2A-NF-ND - KIT DEV BOARD FOR IGBT 其它名稱:835-1063 |
| LV8104V | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:For Variable Speed Control Three-Phase Brushless Motor Predriver |
發布緊急采購，3分鐘左右您將得到回復。