- 您現在的位置：買賣IC網 > PDF目錄358934 > LPC47M14W-NC (SMSC Corporation) SNAP LOCK CABLE MARKER - J (10PK) PDF資料下載
參數資料
| 型號： | LPC47M14W-NC |
| 廠商： | SMSC Corporation |
| 英文描述： | SNAP LOCK CABLE MARKER - J (10PK) |
| 中文描述： | 128引腳ENGANCED超級I / O與LPC接口和USB集線器控制器 |
| 文件頁數： | 113/205頁 |
| 文件大?。?/td> | 1219K |
| 代理商： | LPC47M14W-NC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁當前第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁
SMSC DS – LPC47M14X
Page 113
Rev. 03/19/2001
The operation of the GPIO ports is illustrated in FIGURE 8.
Note:
FIGURE 8 is for illustration purposes only and is not intended to suggest specific implementation details.
Note:
When the following functions are selected, the associated GPIO pins have bi-directional
functionality:
P12, P16, P17 and game port x-axis and y-axis inputs (J1X, J1Y, J2X, J2Y).
When a GPIO port is programmed as an input, reading it through the GPIO data register latches either the inverted or
non-inverted logic value present at the GPIO pin. Writing to a GPIO port that is programmed as an input has no
effect (Table 56)
When a GPIO port is programmed as an output, the logic value or the inverted logic value that has been written into
the GPIO data register is output to the GPIO pin. Reading from a GPIO port that is programmed as an output returns
the last value written to the data register (Table 56). When the GPIO is programmed as an output, the pin is
excluded from the PME and SMI logic.
Table 56 – GPIO Read/Write Behavior
HOST OPERATION
GPIO INPUT PORT
GPIO OUTPUT PORT
READ
LATCHED VALUE OF GPIO PIN
LAST WRITE TO GPIO DATA REGISTER
WRITE
NO EFFECT
BIT PLACED IN GPIO DATA REGISTER
The LPC47M14x provides 31 GPIOs that can directly generate a PME. See the table in the next section. The
polarity bit in the GPIO control registers select the edge on these GPIO pins that will set the associated status bit in
the PME_STS 2 register. The default is the low-to-high edge. If the corresponding enable bit in the PME_EN 2
register and the PME_EN bit in the PME_EN register is set, a PME will be generated. These registers are located in
the PME_BLK of runtime registers which are located at the address contained in the configuration registers 0x60 and
0x61 in Logical Device A. The PME status bits for the GPIOs are cleared on a write of ‘1’. In addition, the
LPC47M14x provides 19 GPIOs that can directly generate an SMI. See the table in the next section.
6.14.5
GPIO PME and SMI Functionality
The following GPIOs are dedicated wakeup GPIOs with a status and enable bit in the PME status and enable
registers:
GP10-GP17
GP20-GP22, GP24-GP27
GP30-GP33
GP41, GP43
GP50-GP57
GP60, GP61
The following PME status and enable registers for these GPIOs:
PME_STS2 and PME_EN2 for GP10-GP17
PME_STS3 and PME_EN3 for GP20-GP22, GP24-GP27
PME_STS4 and PME_EN4 for GP30-GP33, GP41, GP43, GP60 and GP61
PME_STS5 and PME_EN5 for GP50-GP57
The following GPIOs can directly generate an SMI and have a status and enable bit in the SMI status and enable
registers.
GP20-GP22, GP24-GP26
GP30-GP33
GP41, GP42, GP43
GP54-GP57
GP60, GP61
The following SMI status and enable registers for these GPIOs:
SMI_STS3 and SMI_EN3 for GP20-GP22, GP24-GP26 and GP60
SMI_STS4 and SMI_EN4 for GP30-GP33, GP41, GP42, GP43 and GP61
SMI_STS5 and SMI_EN5 for GP54-GP57, FAN_TACH1 and FAN_TACH2
相關PDF資料 |
PDF描述 |
|---|---|
| LPC47M14A-NC | 128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB |
| LPC47M14T-NC | 128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB |
| LPC47M14S-NC | 128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB |
| LPC47M192 | LPC SUPER I/O WITH HARDWARE MONITORING BLOCK |
| LPC47U32X | Peripheral (Multifunction) Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LPC47M14X | 制造商:SMSC 制造商全稱:SMSC 功能描述:128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB |
| LPC47M14X-NC | 制造商:SMSC 制造商全稱:SMSC 功能描述:128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB |
| LPC47M14Y-NC | 制造商:SMSC 制造商全稱:SMSC 功能描述:128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB |
| LPC47M14Z-NC | 制造商:SMSC 制造商全稱:SMSC 功能描述:128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB |
| LPC47M157-NC | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:SMSC 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。