- 您現在的位置：買賣IC網 > PDF目錄383283 > LIS302DLTR (意法半導體) MEMS motion sensor 3-axis - 【2g/【8g smart digital output piccolo accelerometer PDF資料下載
參數資料
| 型號： | LIS302DLTR |
| 廠商： | 意法半導體 |
| 英文描述： | MEMS motion sensor 3-axis - 【2g/【8g smart digital output piccolo accelerometer |
| 中文描述： | MEMS運動傳感器3軸- 【2克/【八克智能數字輸出加速計短笛 |
| 文件頁數： | 15/29頁 |
| 文件大小： | 245K |
| 代理商： | LIS302DLTR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
LIS302DL
Digital Interfaces
15/29
Both the Read Register and Write Register commands are completed in 16 clock pulses or
in multiple of 8 in case of multiple byte read/write. Bit duration is the time between two falling
edges of
SPC
. The first bit (bit 0) starts at the first falling edge of
SPC
after the falling edge
of
CS
while the last bit (bit 15, bit 23, ...) starts at the last falling edge of SPC just before the
rising edge of
CS
.
bit 0
: RW bit. When 0, the data DI(7:0) is written into the device. When 1, the data DO(7:0)
from the device is read. In latter case, the chip will drive
SDO
at the start of bit 8.
bit 1
: MS bit. When 0, the address will remain unchanged in multiple read/write commands.
When 1, the address will be auto incremented in multiple read/write commands.
bit 2-7
: address AD(5:0). This is the address field of the indexed register.
bit 8-15
: data DI(7:0) (write mode). This is the data that will be written into the device (MSb
first).
bit 8-15
: data DO(7:0) (read mode). This is the data that will be read from the device (MSb
first).
In multiple read/write commands further blocks of 8 clock periods will be added. When MS
bit is 0 the address used to read/write data remains the same for every block. When MS bit
is 1 the address used to read/write data is incremented at every block.
The function and the behavior of
SDI
and
SDO
remain unchanged.
5.2.1
SPI Read
Figure 5.
SPI Read protocol
The SPI Read command is performed with 16 clock pulses. Multiple byte read command is
performed adding blocks of 8 clock pulses at the previous one.
bit 0
: READ bit. The value is 1.
bit 1
: MS bit. When 0 do not increment address, when 1 increment address in multiple
reading.
bit 2-7
: address AD(5:0). This is the address field of the indexed register.
bit 8-15
: data DO(7:0) (read mode). This is the data that will be read from the device (MSb
first).
bit 16-...
: data DO(...-8). Further data in multiple byte reading.
CS
SPC
SDI
SDO
RW
DO7DO6DO5DO4DO3DO2DO1DO0
AD5 AD4 AD3 AD2 AD1 AD0
MS
相關PDF資料 |
PDF描述 |
|---|---|
| LIS331AL | MEMS inertial sensor: 3-axis - 【2g analog output “nano” accelerometer |
| LIS331ALTR | MEMS inertial sensor: 3-axis - 【2g analog output “nano” accelerometer |
| LIS331DL | MEMS motion sensor 3-axis - 【2g/【8g smart digital output “nano” accelerometer |
| LIS331DLTR | MEMS motion sensor 3-axis - 【2g/【8g smart digital output “nano” accelerometer |
| LIS3L02AQ3 | MEMS INERTIAL SENSOR: 3-Axis - ?g/?g LINEAR ACCELEROMETER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LIS302DLTR8 | 制造商:STMicroelectronics 功能描述:LIS302DLTR8 - Tape and Reel |
| LIS302DLTR-CUT TAPE | 制造商:ST 功能描述:LIS302DL Series 3 Axis ?/? g 3.3 V Digital Output Piccolo Accerometer - LGA-14 |
| LIS302SG | 功能描述:加速計 - 板上安裝 MEMS MOTION SENSOR 3 AXIS +/-2g Piccolo RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS302SGTR | 功能描述:加速計 - 板上安裝 MEMS motion sensor 3-axis RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS-3-15 | 制造商:TDK-Lambda Corporation 功能描述:15W AC To DC Switching Power Supply - 95-132V/187-265V in - 15V 1A out |
發布緊急采購，3分鐘左右您將得到回復。