- 您現在的位置：買賣IC網 > PDF目錄65794 > LB11825M BRUSHLESS DC MOTOR CONTROLLER, 3 A, PDSO14 PDF資料下載
參數資料
| 型號： | LB11825M |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 3 A, PDSO14 |
| 封裝： | 0.225 ICNH, MFP-14 |
| 文件頁數： | 8/8頁 |
| 文件大?。?/td> | 96K |
| 代理商： | LB11825M |
LB11825M
PS No.7108-8/8
Continued from preceding page.
(3) Described below are the conditions and checkpoints to be observed when setting the constants of the resistor and
capacitor to be externally connected to the R pin and C pin.
1) The maximum value (fOUT1) of the multiplied output frequency to be set must be less than or equal to 1MHz.
2) The R pin voltage and FIL pin voltage must be used within the range 0.3V to (VCC1 - 2.2V). (VCC1 is the
minimum value of the VCC power supply fluctuations, and is equal to or greater than 4.5V.) However, the
lower the R pin voltage, the more easily the multiplied output frequency is affected by ground line noise and
the higher the possibility that it will become unstable. Therefore, a low R pin voltage must not be used if
ground line noise is high.
3) The external resistor (R) connected to the R pin must have a resistance value within the range 6.8k
Ω to 15kΩ.
The R pin itself must be used with a current of not more than 280
μA.
4) The external capacitor (C) connected to the C pin must have a capacitance value within the range 240pF to
1000pF.
5) To increase the variation range for the multiplied output frequency, the values for R and C must be set as high
as possible (within the range below the R1 and C1 calculated values), and components with minimal
fluctuations must be used. To further increase the variation range for the multiplied output frequency, a VCC
voltage greater than 5V must be supplied by, for instance, using the VREG pin (7.1V shunt regulator) of
LB11825M.
5. NC pin
Since this pin is electrically open, it may be used with connections routed through it without posing any problems.
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using
products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd.
products described or contained herein.
SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all
semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or
malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise
to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt
safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not
limited to protective circuits and error prevention circuits for safe design, redundant design, and structural
design.
Upon using the technical information or products described herein, neither warranty nor license shall be granted
with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third
party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's
intellctual property rights which has resulted from the use of the technical information and products mentioned
above.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed
for volume production.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the
SANYO Semiconductor Co.,Ltd. product that you intend to use.
In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are
controlled under any of applicable local export control laws and regulations, such products may require the
export license from the authorities concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise,
without the prior written consent of SANYO Semiconductor Co.,Ltd.
This catalog provides information as of July, 2008. Specifications and information herein are subject
to change without notice.
相關PDF資料 |
PDF描述 |
|---|---|
| LB11867RV | BRUSHLESS DC MOTOR CONTROLLER, 0.02 A, PDSO16 |
| LB11961 | BRUSHLESS DC MOTOR CONTROLLER, 1 A, PDSO16 |
| LB11961 | BRUSHLESS DC MOTOR CONTROLLER, 1 A, PDSO16 |
| LB11967V | BRUSHLESS DC MOTOR CONTROLLER, 0.05 A, PDSO20 |
| LB11967V | BRUSHLESS DC MOTOR CONTROLLER, 0.6 A, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB11826 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:For OA Products Three-Phase Brushless Motor Driver |
| LB11826_08 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:For OA Products Three-Phase Brushless Motor Driver |
| LB11826-E | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB11827 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Three-Phase Brushless Motor Driver for OA Products |
| LB11847 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:PWM Current Control Type Stepping Motor Driver |
發布緊急采購，3分鐘左右您將得到回復。