- 您現在的位置：買賣IC網 > PDF目錄374269 > K4H511638 (SAMSUNG SEMICONDUCTOR CO. LTD.) 512Mb C-die DDR SDRAM Specification PDF資料下載
參數資料
| 型號： | K4H511638 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | 512Mb C-die DDR SDRAM Specification |
| 中文描述： | 葷的512Mb芯片DDR SDRAM內存規格 |
| 文件頁數： | 20/24頁 |
| 文件大小： | 367K |
| 代理商： | K4H511638 |
Rev. 1.1 June. 2005
DDR SDRAM
DDR SDRAM 512Mb C-die (x4, x8, x16)
b. Pulldown slew rate is measured under the test conditions shown in Figure 3.
Output
Test point
VDDQ
50
Figure 3 : Pulldown slew rate test load
c. Pullup slew rate is measured between (VDDQ/2 - 320 mV +/- 250 mV)
Pulldown slew rate is measured between (VDDQ/2 + 320 mV +/- 250 mV)
Pullup and Pulldown slew rate conditions are to be met for any pattern of data, including all outputs switching and only one output
switching.
Example : For typical slew rate, DQ0 is switching
For minmum slew rate, all DQ bits are switching from either high to low, or low to high.
The remaining DQ bits remain the same as for previous state.
d. Evaluation conditions
Typical : 25
°
C (T Ambient), VDDQ = 2.5V(for DDR266/333) and 2.6V(for DDR400), typical process
Minimum : 70
°
C (T Ambient), VDDQ = 2.3V(for DDR266/333) and 2.5V(for DDR400), slow - slow process
Maximum : 0
°
C (T Ambient), VDDQ = 2.7V(for DDR266/333) and 2.7V(for DDR400), fast - fast process
e. The ratio of pullup slew rate to pulldown slew rate is specified for the same temperature and voltage, over the entire temperature and
voltage range. For a given output, it represents the maximum difference between pullup and pulldown drivers due to process variation.
f. Verified under typical conditions for qualification purposes.
g. TSOPII package divices only.
h. Only intended for operation up to 266 Mbps per pin.
i. A derating factor will be used to increase tIS and tIH in the case where the input slew rate is below 0.5V/ns
as shown in Table 2. The Input slew rate is based on the lesser of the slew rates detemined by either VIH(AC) to VIL(AC) or
VIH(DC) to VIL(DC), similarly for rising transitions.
j. A derating factor will be used to increase tDS and tDH in the case where DQ, DM, and DQS slew rates differ, as shown in Tables 3 & 4.
Input slew rate is based on the larger of AC-AC delta rise, fall rate and DC-DC delta rise, Input slew rate is based on the lesser of the
slew rates determined by either VIH(AC) to VIL(AC) or VIH(DC) to VIL(DC), similarly for rising transitions.
The delta rise/fall rate is calculated as:
{1/(Slew Rate1)} - {1/(Slew Rate2)}
For example : If Slew Rate 1 is 0.5 V/ns and slew Rate 2 is 0.4 V/ns, then the delta rise, fall rate is - 0.5ns/V . Using the table given, this
would result in the need for an increase in tDS and tDH of 100 ps.
k. Table 3 is used to increase tDS and tDH in the case where the I/O slew rate is below 0.5 V/ns. The I/O slew rate is based on the lesser
on the lesser of the AC - AC slew rate and the DC- DC slew rate. The inut slew rate is based on the lesser of the slew rates deter
mined by either VIH(ac) to VIL(ac) or VIH(DC) to VIL(DC), and similarly for rising transitions.
m. DQS, DM, and DQ input slew rate is specified to prevent double clocking of data and preserve setup and hold times. Signal transi
tions through the DC region must be monotonic.
a. Pullup slew rate is characteristized under the test conditions as shown in Figure 2.
Output
Test point
VSSQ
50
Figure 2 : Pullup slew rate test load
22.0 System Notes
相關PDF資料 |
PDF描述 |
|---|---|
| K4H511638C-UC | 512Mb C-die DDR SDRAM Specification |
| K4H510438C-ZLCC | DIN Audio Connector; No. of Contacts:6; Contact Termination:Solder; Mounting Type:Cable; Gender:Male RoHS Compliant: Yes |
| K4H511638C-ZLCC | DIN Audio Connector; No. of Contacts:8; Contact Termination:Solder; Mounting Type:Cable; Gender:Male RoHS Compliant: Yes |
| K4H510438C-ZLB3 | Connector Kit; Contents Of Kit:C14610F0240031 24 position bulkhead housing single latch spring cover, C14610B0241021 24 position female insert wire protect, With spring cover; For Use With:C146 Heavy Duty Industrial Connectors RoHS Compliant: Yes |
| K4H511638C-ZLB3 | Connector Kit; Contents Of Kit:C14610G0246008 24 position hood PG 21 double latch high profile top entry, C14610A0241021 24 position male insert wire protect, VN162100014 PG 21 gland bushing, For 0.433" - 0.866" diameter cable RoHS Compliant: Yes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| K4H511638A-TCA0 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:128Mb DDR SDRAM |
| K4H511638A-TCA2 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:128Mb DDR SDRAM |
| K4H511638A-TCB0 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:128Mb DDR SDRAM |
| K4H511638A-TLA0 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:128Mb DDR SDRAM |
| K4H511638A-TLA2 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:128Mb DDR SDRAM |
發布緊急采購，3分鐘左右您將得到回復。