參數資料
型號： IDT7290820JG
廠商： IDT, Integrated Device Technology Inc
文件頁數： 22/27頁
文件大?。?/td> 0K
描述： IC DGTL SW 2048X2048 84-PLCC
標準包裝： 30
系列： 7200
類型： 多路復用器
電路： 1 x 16:16
獨立電路： 1
電壓電源： 單電源
電源電壓： 4.75 V ~ 5.25 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 84-LCC（J 形引線）
供應商設備封裝： 84-PLCC（29.21x29.21）
包裝： 管件
其它名稱： 7290820JG
4
COMMERCIALTEMPERATURERANGE
IDT7290820 5V TIME SLOT INTERCHANGE
DIGITAL SWITCH 2,048 x 2,048
PIN DESCRIPTION
SYMBOL
NAME
I/O
DESCRIPTION
GND
Ground.
Ground Rail.
Vcc
+5.0 Volt Power Supply.
TX0-15(1)
TX Output 0 to 15
O
Serial data output stream. These streams may have data rates of 2.048, 4.096 or 8.192 Mb/s, depending upon
(Three-state Outputs)
the value programmed at bits DR0-1 in the IMS register.
RX0-15(1)
RX Input 0 to 15
I
Serial data input stream. These streams may have data rates of 2.048, 4.096 or 8.192 Mb/s, depending upon
the value programmed at bits DR0-1 in the IMS register.
F0i(1)
Frame Pulse
I
When the WFPS pin is LOW, this input accepts and automatically identifies frame synchronization signals formatted
according to ST-BUS and GCI specifications. When the WFPS pin is HIGH, this pin accepts a negative frame
pulse which conforms to WFPS formats.
FE/HCLK(1) Frame Evaluation/
I
When the WFPS pin is LOW, this pin is the frame measurement input. When the WFPS pin is HIGH, the HCLK
HCLK Clock
(4.096 MHz clock) is required for frame alignment in the wide frame pulse (WFP) mode.
CLK(1)
Clock
I
Serial clock for shifting data in/out on the serial streams (RX/TX 0-15). Depending upon the value programmed
at bits DR0-1 in the IMS register, this input accepts a 4.096, 8.192 or 16.384 MHz clock.
TMS
Test Mode Select
I
JTAG signal that controls the state transitions of the TAP controller. This pin is pulled HIGH by an internal pull-
up when not driven.
TDI
Test Serial Data In
I
JTAG serial test instructions and data are shifted in on this pin. This pin is pulled HIGH by an internal pull-up
when not driven.
TDO
Test Serial Data Out
O
JTAG serial data is output on this pin on the falling edge of TCK. This pin is held in high-impedance state when
JTAG scan is not enabled.
TCK(1)
Test Clock
I
Provides the clock to the JTAG test logic. This pin is pulled high by an internal pull-up when not driven.
TRST
Test Reset
I
Asynchronously initializes the JTAG TAP controller by putting it in the Test-Logic-reset state. This pin is pulled
by an internal pull-up when not driven. This pin should be pulsed LOW on power-up, or held LOW, to ensure
that the IDT7290820 is in the normal functional mode.
IC(1)
Internal Connection
I
Connect to GND for normal operation. This pin must be LOW for the IDT7290820 to function normally and to
comply with IEEE 1114 (JTAG) boundary scan requirements.
RESET(1)
Device Reset
I
This input (active LOW) puts the IDT7290820 in its reset state that clears the device internal counters, registers
(Schmitt Trigger Input)
and brings TX0-15 and microport data outputs to a high-impedance state. The time constant for a power up
reset circuit must be a minimum of five times the rise time of the power supply. In normal operation, the
RESET
pin must be held LOW for a minimum of 100ns to reset the device.
WFPS(1)
Wide Frame
I
When 1, enables the wide frame pulse (WFP) Frame Alignment interface. When 0, the device operates in
Pulse Select
ST-BUS/GCI mode.
A0-7(1)
Address 0-7
I
When non-multiplexed CPU bus operation is selected, these lines provide the A0-A7 address lines to the internal
memories.
DS/
RD(1)
Data Strobe/Read
I
For Motorola multiplexed bus operation, this input is DS. This active HIGH DS input works in conjunction with
CS
to enable the read and write operations. For Motorola non-multiplexed CPU bus operation, this input is DS. This
active LOW input works in conjunction with
CS to enable the read and write operations. For Intel multiplexed bus
operation, this input is
RD. This active LOW input sets the data bus lines (AD0-7, D8-15) as outputs.
R/
W / WR(1) Read/Write / Write
I
In the cases of Motorola non-multiplexed and multiplexed bus operations, this input is R/
W. This input controls
the direction of the data bus lines (AD0-7, D8-15) during a microprocessor access. For Intel multiplexed bus
operation, this input is
WR. This active LOW input is used with RD to control the data bus (AD0-7) lines as inputs.
CS(1)
Chip Select
I
Active LOW input used by a microprocessor to activate the microprocessor port of IDT7290820.
AS/ALE(1)
Address Strobe or
I
This input is used if multiplexed bus operation is selected via the IM input pin. For Motorola non-multiplexed
Latch Enable
bus operation, connect this pin to ground. This pin is pulled low by an internal pull-down when not driven.
IM(1)
CPU Interface Mode
I
When IM is HIGH, the microprocessor port is in the multiplexed mode. When IM is LOW, the microprocessor
port is in non-multiplexed mode. This pin is pulled low by an internal pull-down when not driven.
AD0-7(1)
Address/Data Bus 0 to 7 I/O
These pins are the eight least significant data bits of the microprocessor port. In multiplexed mode, these pins
are also the input address bits of the microprocessor port.
NOTE:
1. These pins are 5V tolerant.
相關PDF資料
PDF描述
MAX5527GUA+T IC POT DGTL 1TIME PROGR 8-UMAX
IDT7290820J IC DGTL SW 2048X2048 84-PLCC
VI-BWW-MY-F2 CONVERTER MOD DC/DC 5.5V 50W
VI-BWW-MY-F1 CONVERTER MOD DC/DC 5.5V 50W
VI-BW0-MY-F4 CONVERTER MOD DC/DC 5V 50W
相關代理商/技術參數
參數描述
IDT7290820JG8 功能描述:IC DGTL SW 2048X2048 84-PLCC RoHS:是 類別:集成電路 (IC) >> 邏輯 - 信號開關，多路復用器，解碼器 系列:7200 標準包裝:48 系列:74VHC 類型:多路復用器 電路:4 x 2:1 獨立電路:1 輸出電流高，低:8mA，8mA 電壓電源:單電源 電源電壓:2 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:管件
IDT7290820PQF 功能描述:IC DGTL SW 2048X2048 100-PQFP RoHS:否 類別:集成電路 (IC) >> 邏輯 - 信號開關，多路復用器，解碼器 系列:7200 標準包裝:48 系列:74VHC 類型:多路復用器 電路:4 x 2:1 獨立電路:1 輸出電流高，低:8mA，8mA 電壓電源:單電源 電源電壓:2 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:管件
IDT7290820PQFG 功能描述:IC DGTL SW 2048X2048 100-PQFP RoHS:是 類別:集成電路 (IC) >> 邏輯 - 信號開關，多路復用器，解碼器 系列:7200 標準包裝:48 系列:74VHC 類型:多路復用器 電路:4 x 2:1 獨立電路:1 輸出電流高，低:8mA，8mA 電壓電源:單電源 電源電壓:2 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:管件
IDT72EBV73273 功能描述:BOARD EVALUATION RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081
IDT72P51339L5BB 功能描述:IC FLOW CTRL 36BIT 256-BGA RoHS:否 類別:集成電路 (IC) >> 專用 IC 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*