- 您現在的位置：買賣IC網 > PDF目錄384479 > ICS1702 (Electronic Theatre Controls, Inc.) QuickSaver Charge Controller for Nickel-Cadmium and Nickel-Metal Hydride Batteries PDF資料下載
參數資料
| 型號： | ICS1702 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | QuickSaver Charge Controller for Nickel-Cadmium and Nickel-Metal Hydride Batteries |
| 中文描述： | QuickSaver充電控制器的鎳鎘和鎳氫電池 |
| 文件頁數： | 15/28頁 |
| 文件大小： | 466K |
| 代理商： | ICS1702 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
15
ICS1702
Figure 12: Thermal switch to connection to
ground at the THERM pin
Table 7: Thermal Switch Voltage Thresholds
The 4%/min., 3%/min. and 2%/min. decrease in thermistor
resistance for the last minute of charge for the selected charge rate
are applicable for NTC thermistors other than 10k
@ 25
°
C
provided that the following requirements are met:
An external pull-up resistor to 5V is used to provide a
thermistor voltage of 1.67V @ 25
°
C.
The thermistor resistance at 25
°
C does not exceed 20k
so
that accuracy and adequate noise immunity are maintained.
The thermistor resistance increases by a factor of about 1.8
from 25
°
C to 10
°
C and the thermistor resistance decreases by
a factor of about 2.1 from 25
°
C to 45
°
C.
Using a thermal switch for hot battery detection:
A thermal switch that opens at about 45
°
C is recommended. The
thermal switch must be connected between the THERM pin and
ground. When the thermal switch is closed, the voltage at the
THERM pin must be below 0.5V for normal operation. When the
thermal switch opens (see Figure 12), the internal pull-up at the
THERM pin will raise the voltage above 4.2V and the
ICS1702
will shut down and will not restart unless reset. Table 7 contains
the internal voltage thresholds used with a thermal switch.
For example, a battery was monitored as it charged at a 1C rate in
25
°
C ambient. In the final minute of charge, the battery
temperature rose from 29.8
°
C to 31
°
C where full charge was
detected. With this data, the typical 10k
@ 25
°
C thermistor used
in the example above is checked to determine if its characteristics
satisfy the 4% decrease in resistance required for the last minute of
charge. The thermistor measures 8.37k
@ 29.8
°
C and 8.01k
at
31
°
C. For a 1C charge rate, the resistance must decrease at least
4%/min. or more between 29.8
°
C and 31
°
C. The percent decrease
in resistance for the thermistor is calculated as:
8.37k
- 8.01k
(100) =4.30%
8.37k
This thermistor meets the 4%/min. requirement and will result in
termination at full charge at 31
°
C. The thermistor must be checked
for a 4%/min. decrease in resistance for the last minute of charge
near the hot and cold battery thresholds.
The battery in the example above was charged in a 25
°
C ambient
with its temperature rising 31
°
C - 25
°
C or 6
°
C. The temperature
rise was 31
°
C - 29.8
°
C or 1.2
°
C in the last minute before full
charge occurred. This information is used to check the thermistor
characteristics at the ambient extremes. If the selected 1C charge
rate is initiated at 12
°
C, the thermistor resistance change must
decrease 4%/min. between 16.8
°
C and 18
°
C. The thermistor
resistance at 16.8
°
C is 13.68k
and at 18
°
C the thermistor
resistance is 13.06k
.
13.68k
- 13.06k
(100) =4.53%
13.68k
The thermistor meets the 4%/min. requirement and will result in
termination of fast charge at 18
°
C. If the selected 1C charge rate is
initiated at 37
°
C, the thermistor resistance change must decrease
4%/min. between 41.8
°
C and 43
°
C. The thermistor resistance at
41.8
°
C is 5.48k
and at 43
°
C the thermistor resistance is 5.25k
.
5.48k
-5.25k
(100) =4.19%
5.48k
The thermistor meets the 4%/min. requirement and will result in
termination of fast charge at 43
°
C.
THERM pin
R = 75k
normally closed thermal switch
opens at 45oC
V
DD
Parameter
Voltage
Battery
Temperature
>45
°
C
Open Thermal Switch
Voltage
Closed Thermal Switch
Voltage
>4.2
<0.5
<45
°
C
相關PDF資料 |
PDF描述 |
|---|---|
| ICS1702M | QuickSaver Charge Controller for Nickel-Cadmium and Nickel-Metal Hydride Batteries |
| ICS662-03 | HDTV Audio/Video Clock Source |
| ICS66203 | HDTV Audio/Video Clock Source |
| ICS94222 | Programmable System Frequency Generator for PII/III⑩ |
| ICT-xxx | TRANSIENT ABSORPTION ZENER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS1702M | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:QuickSaver Charge Controller for Nickel-Cadmium and Nickel-Metal Hydride Batteries |
| ICS1702MT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:QuickSaver Charge Controller for Nickel-Cadmium and Nickel-Metal Hydride Batteries |
| ICS1702N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:QuickSaver Charge Controller for Nickel-Cadmium and Nickel-Metal Hydride Batteries |
| ICS1705 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| ICS1708 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:QuickSaver Charge Control IC for Nickel-Cadmium and Nickel-Metal Hydride Batteries |
發布緊急采購，3分鐘左右您將得到回復。