參數資料
型號: MC12439
廠商: Motorola, Inc.
英文描述: HIGH FREQUENCY PLL CLOCK GENERATOR
中文描述: 高頻PLL時鐘發生器
文件頁數: 2/11頁
文件大?。?/td> 131K
代理商: MC12439
MC12439
MOTOROLA
TIMING SOLUTIONS
BR1333 — Rev 6
2
1
N[1]
N[0]
NC
XTAL_SEL
M[6]
M[5]
M[4]
XTAL1
FREF_EXT
PWR_DOWN
PLL–VCC
S_LOAD
S_DATA
S_CLOCK
4
3
2
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
7
8
6
5
Figure 1. 28–Lead Pinout
(Top View)
P_LOAD
VCC
FOUT
FOUT GND
VCC
TEST GND
M[3]
M[2]
M[1]
M[0]
OE
XTAL2
N[1:0]
0 0
0 1
1 0
1 1
Output Division
2
4
8
1
Input
PWR_DOWN
XTAL_SEL
OE
0
FOUT
FREF_EXT
Disabled
1
FOUT/16
XTAL
Enabled
PIN DESCRIPTIONS
Pin Name
Type
Function
Inputs
XTAL1, XTAL2
These pins form an oscillator when connected to an external series–resonant crystal.
S_LOAD
Int. Pulldown
This pin loads the configuration latches with the contents of the shift registers. The latches will be
transparent when this signal is HIGH, thus the data must be stable on the HIGH–to–LOW transition of
S_LOAD for proper operation.
S_DATA
Int. Pulldown
This pin acts as the data input to the serial configuration shift registers.
S_CLOCK
Int. Pulldown
This pin serves to clock the serial configuration shift registers. Data from S_DATA is sampled on the rising
edge.
P_LOAD
Int. Pullup
This pin loads the configuration latches with the contents of the parallel inputs .The latches will be
transparent when this signal is LOW, thus the parallel data must be stable on the LOW–to–HIGH transition
of P_LOAD for proper operation.
M[6:0]
Int. Pullup
These pins are used to configure the PLL loop divider. They are sampled on the LOW–to–HIGH transition
of P_LOAD. M[6] is the MSB, M[0] is the LSB.
N[1:0]
Int. Pullup
These pins are used to configure the output divider modulus. They are sampled on the LOW–to–HIGH
transition of P_LOAD.
OE
Int. Pullup
Active HIGH Output Enable.
Outputs
FOUT, FOUT
These differential positive–referenced ECL signals (PECL) are the output of the synthesizer.
TEST
The function of this output is determined by the serial configuration bits T[2:0].
Power
VCC
This is the positive supply for the chip, and is connected to +3.3V or 5.0V (VCC = PLL_VCC).
PLL_VCC
This is the positive supply for the PLL, and should be as noise–free as possible for low–jitter operation. This
supply is connected to +3.3V or 5.0V (VCC = PLL_VCC).
GND
These pins are the negative supply for the chip and are normally all connected to ground.
Other
PWR_DOWN
Int. Pulldown
LVCMOS input that forces the FOUT output to synchronously reduce its frequency by a factor of 16.
FREF_EXT
Int. Pulldown
LVCMOS input which can be used as the PLL reference frequency.
XTAL_SEL
Int. Pullup
LVCMOS input that selects between the XTAL and FREF_EXT PLL reference inputs. A HIGH selects the
XTAL input.
相關PDF資料
PDF描述
MC13146FTA LOW POWER DC - 2.0 GHz TRANSMITTER
MC13146 LOW POWER DC - 2.0 GHz TRANSMITTER
MC13159DTB WIDEBAND FM IF SUBSYSTEM FOR PHS AND DIGITAL APPLICATIONS
MC13159 WIDEBAND FM IF SUBSYSTEM FOR PHS AND DIGITAL APPLICATIONS
MC13282AP 100 MHz VIDEO PROCESSOR WITH OSD INTERFACE
相關代理商/技術參數
參數描述
MC12439FN 制造商:Motorola Inc 功能描述: 制造商:Motorola Inc 功能描述:MISCELLANEOUS CLOCK GENERATOR, 28 Pin, Plastic, PLCC
MC1243F 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC1245L 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC1246L 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC1247F 制造商:Rochester Electronics LLC 功能描述:- Bulk