- 您現在的位置：買賣IC網 > PDF目錄378513 > CY7C63231A (Cypress Semiconductor Corp.) enCoRe USB Low-speed USB Peripheral Controller(enCoRe USB 低速USB外設控制器) PDF資料下載
參數資料
| 型號： | CY7C63231A |
| 廠商： | Cypress Semiconductor Corp. |
| 英文描述： | enCoRe USB Low-speed USB Peripheral Controller(enCoRe USB 低速USB外設控制器) |
| 中文描述： | 的enCoRe USB低速USB外設控制器（的enCoRe的USB低速的USB外設控制器） |
| 文件頁數： | 8/50頁 |
| 文件大?。?/td> | 1036K |
| 代理商： | CY7C63231A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
FOR
FOR
enCoRe
USB
CY7C63221/31A
Document #: 38-08028 Rev. *B
Page 8 of 50
6.0
Programming Model
Refer to the
CYASM Assembler User’s Guide
for more details on firmware operation with the microcontrollers.
6.1
The 14-bit program counter (PC) allows access for 3 Kbytes of EPROM using the architecture. The program counter is cleared
during reset, such that the first instruction executed after a reset is at address 0x0000. This is typically a jump instruction to a
reset handler that initializes the application.
The lower 8 bits of the program counter are incremented as instructions are loaded and executed. The upper 6 bits of the program
counter are incremented by executing an XPAGE instruction. As a result, the last instruction executed within a 256-byte “page”
of sequential code should be an XPAGE instruction. The assembler directive “XPAGEON” will cause the assembler to insert
XPAGE instructions automatically. As instructions can be either one or two bytes long, the assembler may occasionally need to
insert a NOP followed by an XPAGE for correct execution.
The program counter of the next instruction to be executed, carry flag, and zero flag are saved as two bytes on the program stack
during an interrupt acknowledge or a CALL instruction. The program counter, carry flag, and zero flag are restored from the
program stack only during a RETI instruction.
Please note the program counter cannot be accessed directly by the firmware. The program stack can be examined by reading
SRAM from location 0x00 and up.
Note that there are restrictions in using the JMP, CALL, and INDEX instructions across the 4-KB boundary of the program memory.
Refer to the
CYASM Assembler User’s Guide
for a detailed description.
Program Counter (PC)
6.2
The accumulator is the general-purpose, do-everything register in the architecture where results are usually calculated.
8-bit Accumulator (A)
6.3
The index register “X” is available to the firmware as an auxiliary accumulator. The X register also allows the processor to perform
indexed operations by loading an index value into X.
8-bit Index Register (X)
6.4
During a reset, the program stack pointer (PSP) is set to zero. This means the program “stack” starts at RAM address 0x00 and
“grows” upward from there. Note that the program stack pointer is directly addressable under firmware control, using the MOV
PSP,A instruction. The PSP supports interrupt service under hardware control and CALL, RET, and RETI instructions under
firmware control.
During an interrupt acknowledge, interrupts are disabled and the program counter, carry flag, and zero flag are written as two
bytes of data memory. The first byte is stored in the memory addressed by the program stack pointer, then the PSP is incremented.
The second byte is stored in memory addressed by the program stack pointer and the PSP is incremented again. The net effect
is to store the program counter and flags on the program “stack” and increment the program stack pointer by two.
The return from interrupt (RETI) instruction decrements the program stack pointer, then restores the second byte from memory
addressed by the PSP. The program stack pointer is decremented again and the first byte is restored from memory addressed
by the PSP. After the program counter and flags have been restored from stack, the interrupts are enabled. The effect is to restore
the program counter and flags from the program stack, decrement the program stack pointer by two, and re-enable interrupts.
8-bit Program Stack Pointer (PSP)
XTALIN/P2.1
XTALOUT/P2.2
IN
IN
8
9
9
10
6-MHz ceramic resonator or external clock input, or P2.1 input
6-MHz ceramic resonator return pin or internal oscillator output,
or P2.2 input
Programming voltage supply, ground for normal operation
Voltage supply
Voltage supply for 1.3-k
USB pull-up resistor (3.3V nominal).
Also serves as P2.0 input.
Ground
V
PP
V
CC
VREG/P2.0
6
7
11
8
10
7
V
SS
5
6
5.0
Pin Assignments (continued)
Name
I/O
CY7C63231A/
CY7C63221A-XC
18-Pin/Pad
Description
16-Pin
相關PDF資料 |
PDF描述 |
|---|---|
| CY7C64013C | Full-Speed USB (12-Mbps)(全速USB(12-Mbps)) |
| CY7C64113C | Full-Speed USB (12-Mbps)(全速USB(12-Mbps)) |
| CY7C64013 | Full-Speed USB (12 Mbps) Function(全速 USB (12 Mbps)性能) |
| CY7C64113 | Full-Speed USB (12 Mbps) Function(全速 USB (12 Mbps)性能) |
| CY7C64713 | EZ-USB FX1 USB Microcontroller Full-speed USB Peripheral Controller(EZ-USB FX1 USB微控制器，全速USB外設控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CY7C63231A-PXC | 功能描述:8位微控制器 -MCU enCoRe RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| CY7C63231A-SC | 功能描述:IC MCU 3K USB LS PERIPH 18-SOIC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器 - 特定應用 系列:enCoRe™ 產品變化通告:Product Discontinuation 26/Aug/2009 標準包裝:250 系列:- 應用:網絡處理器 核心處理器:4Kc 程序存儲器類型:- 控制器系列:- RAM 容量:16K x 8 接口:以太網，UART，USB 輸入/輸出數:- 電源電壓:1.8V, 3.3V 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:208-LQFP 包裝:帶卷 (TR) 供應商設備封裝:PG-LQFP-208 其它名稱:SP000314382 |
| CY7C63231A-SXC | 功能描述:8位微控制器 -MCU enCoRe RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| CY7C63231A-SXCT | 功能描述:IC MCU 3K USB LS PERIPH 18-SOIC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器 - 特定應用 系列:enCoRe™ 產品變化通告:Product Discontinuation 26/Aug/2009 標準包裝:250 系列:- 應用:網絡處理器 核心處理器:4Kc 程序存儲器類型:- 控制器系列:- RAM 容量:16K x 8 接口:以太網，UART，USB 輸入/輸出數:- 電源電壓:1.8V, 3.3V 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:208-LQFP 包裝:帶卷 (TR) 供應商設備封裝:PG-LQFP-208 其它名稱:SP000314382 |
| CY7C63310-PXC | 功能描述:USB 接口集成電路 USB 3K Flash 128 byte RAM COM RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
發布緊急采購，3分鐘左右您將得到回復。