- 您現在的位置：買賣IC網 > PDF目錄384476 > I7032-EN (Electronic Theatre Controls, Inc.) 200 Mbps Laser-Diode Driver PDF資料下載
參數資料
| 型號： | I7032-EN |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 200 Mbps Laser-Diode Driver |
| 中文描述： | 200 Mbps的激光二極管驅動器 |
| 文件頁數： | 7/14頁 |
| 文件大小： | 211K |
| 代理商： | I7032-EN |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁
i7032
5. Product description
The i7032 consists of a laser bias generator
with
automatic
power
modulation current driver, and a reference
generator with temperature compensation.
control
(APC),
a
5.1. Modulation circuitry
The modulator output stage is designed to
drive up to 80mA into 25
load in either AC-
couple or DC-coupled mode. The amplitude of
the modulation current is set with a resistor at
IMODSET pin or with resistors at IMODSET and
IMODTC pins. Please refer to 4.3. Typical
operating characteristics figure 5 and figure 7 for
more information.
The input swing is required to completely
switch the output stage depends on both R
OASDJ
and modulation current.
5.2. Automatic power control
The amplitude of DC current to the laser
diode is determined by setting the resistor at
IBIASSET pin (Please refer to 4.3. Typical
operating characteristics figure 4). To maintain
constant
average
optical
incorporates a control loop to compensate for
change
in
laser
threshold
temperature and lifetime.
power,
i7032
current
over
A monitor photodiode mounted in the laser
package is used to convert the optical power into
a monitor current. This current flow into the IPIN
input. The IPINSET current mirror draws current
away from IPIN node. When the current into IPIN
node equals the current drawn away by IPINSET,
the node voltage is set by 4/7xVcc reference.
When the monitor current exceeds IPINSET, the
IPIN node voltage will be forced higher. If the
monitor current decreases, the IPIN node voltage
is decreased. In either case the voltage change
results in a feedback current at IBIASFB node.
5.3. APC failure Indicator
The i7032 provides an APC failure indicator
to indicate an APC loop tacking failure. FAILOUT
is set low when the APC loop can no longer
adjust the bias current to maintain the desired
monitor current. This output is pulled up to Vcc
through an external 2.7K
resistor.
5.4. Enable inputs
The i7032 provides complementary enable
inputs (ENB+, ENB-). The laser is disabled by
reducing the reference voltage outputs (VREF1,
VREF2). Both ENB+ and ENB- pins can not be
floating and only one logic state enables laser
operation (please refer to Table 1).
ENB-
ENB+
VREF
0
0
Off
0
1
On
1
0
Off
1
1
Off
Table 1. i7032 truth table
2003 iCreate Technologies Corporation
This document contains preliminary information on product but not yet fully characterized.
iCreate Technologies Corporation reserves the right to change the specification in any manner without notice.
Page 5
ICR-DS-i7032001
相關PDF資料 |
PDF描述 |
|---|---|
| I7032-ET | 200 Mbps Laser-Diode Driver |
| I7110 | 300 Mbps LED Drivers |
| I7110-EG | 300 Mbps LED Drivers |
| I7110-EP | 300 Mbps LED Drivers |
| I7110-ES | 300 Mbps LED Drivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| I7032-ET | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:200 Mbps Laser-Diode Driver |
| I-7050 | 制造商:ICP DAS USA, IN 功能描述:DATA LOGGER,RS-485,100Hz,16BIT,7 CHANNEL DIGITAL. IN/8 CHANN |
| I-7050D | 制造商:ICP DAS USA INC 功能描述:MODULE,7 DIGITAL INPUT AND 8 DIGITAL OUTPUT |
| I705-13G-2388 | 制造商:DRUCK 功能描述:DPI705-20BAR INDICATOR RC |
| I-7053_FG | 制造商:ICP DAS USA, IN 功能描述:DATA LOGGER,RS-485,100Hz,16BIT,NON-ISOLATED 16 CHANNEL DIGIT |
發布緊急采購，3分鐘左右您將得到回復。