- 您現(xiàn)在的位置：買賣IC網 > PDF目錄384450 > HV100DB1 (Supertex, Inc.) 3-Pin Hotswap Controller PDF資料下載
參數資料
| 型號： | HV100DB1 |
| 廠商： | Supertex, Inc. |
| 英文描述： | 3-Pin Hotswap Controller |
| 中文描述： | 3引腳熱插拔控制器 |
| 文件頁數： | 4/5頁 |
| 文件大?。?/td> | 83K |
| 代理商： | HV100DB1 |
4
HV100/HV101
Application Information
Turn On Clamp
Hotswap controllers using a MOSFET as the pass element all
include a capacitor divider from V
to V
through C
, C
and C
. In most competitive solutions a large external capacitor
is added to the gate of the pass element to limit the voltage on
the gate resulting from this divider. In those instances if a gate
capacitor is not used the internal circuitry is not available to hold
off the gate and therefore a fast rising voltage input will cause the
pass element to turn on for a moment. This allows current spikes
to pass through the MOSFET.
The HV100/HV101 include a built-in clamp to ensure that this
spurious current glitch does not occur. The built-in clamp will
work for the time constants of most mechanical connectors.
There may be applications, however, that have rise times that
are much less than 1
μ
s (100
’
s of ns). In these instances it may
be necessary to add a capacitor from the MOSFET gate to
source to clamp the gate and suppress this current spike. In
these cases the current spike generally contains very little
energy and does not cause damage even if a capacitor is not
used at the gate.
Auto-Adapt Operation
The HV100/HV101 Auto-adapt mechanism provides an impor-
tant function. It normalizes the hotswap period regardless of
pass element or load capacitor for consistent hotswap results.
By doing this it allows the novel short circuit mechanism to work
because the mechanism requires a known time base.
The above diagram illustrates the effectiveness of the auto-
adapt mechanism. In this example three MOSFETs with different
C
and R
values are used. The top waveform is the hotswap
current, while the bottom waveform is the gate voltage. As can
be seen, the hotswap period is normalized, the initial slope of the
gate voltage is approximately 2.5V/ms regardless of the MOSFET,
and the total hotswap period and peak currents are a function of
a MOSFET type dependent constant multiplied by C
LOAD
.
Typically if MOSFETs of the same type are used, the hotswap
results will be extremely consistent. If different types are used
they will usually exhibit minimal variation.
Short Circuit Protection
The HV100/HV101 provide short circuit protection by shutting
down if the Miller Effect associated with hotswap does not occur.
Specifically, if the output is shorted then the gate will rise without
exhibiting a
“
flat response
”
. Due to the fact that we have normal-
ized the hotswap period for any pass element, a timer can be
used to detect if the gate voltage rises above a threshold within
that time, indicating that a short exists. The diagram below
shows a typical turn on sequence with the load shorted, resulting
in a peak current of 4A.
The maximum current that may occur during this period can be
controlled by adding a resistor in series with the source of the
MOSFET. The lower graph shows the same circuit with a 100m
resistor inserted between source and V
NN
. In this case the
maximum current is 25% smaller.
For most applications and pass elements, the HV100/HV101
provides adequate limiting of the maximum current to prevent
damage without the need for any external components. The 2.5s
delay of the auto-retry circuit provides time for the pass element
to cool between attempts.
2A/div
NTE66 is a trademark of NTE Electronics
IRF530 is a trademark of International Rectifier Corporation
IRF120M is a trademark of International Rectifier Corporation
相關PDF資料 |
PDF描述 |
|---|---|
| HV100K5 | 3-Pin Hotswap, Inrush Current Limiter Controllers |
| HV100K6 | 3-Pin Hotswap, Inrush Current Limiter Controllers |
| HV100X | 3-Pin Hotswap, Inrush Current Limiter Controllers |
| HV20220 | Low Charge Injection 8-Channel High Voltage Analog Switch(低電荷射入8通道高壓模擬開關) |
| HV20320 | Low Charge Injection 8-Channel High Voltage Analog Switch(低電荷射入8通道高壓模擬開關) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HV100K5 | 功能描述:熱插拔功率分布 Negative RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| HV100K5-G | 功能描述:熱插拔功率分布 Negative RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| HV100K6 | 制造商:SUPERTEX 制造商全稱:SUPERTEX 功能描述:3-Pin Hotswap, Inrush Current Limiter Controllers |
| HV100M2EB-1021(E) | 制造商:SPC Multicomp 功能描述:CAPACITOR 10UF 250V |
| HV100M2WB-1326(E) | 制造商:SPC Multicomp 功能描述:CAPACITOR 10UF 450V |
發(fā)布緊急采購，3分鐘左右您將得到回復。