- 您現在的位置：買賣IC網 > PDF目錄384445 > HTSMOH5601EV (NXP SEMICONDUCTORS) HITAG S transponder IC PDF資料下載
參數資料
| 型號： | HTSMOH5601EV |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 通信及網絡 |
| 英文描述： | HITAG S transponder IC |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, UUC |
| 封裝： | MOA2 |
| 文件頁數： | 7/21頁 |
| 文件大?。?/td> | 162K |
| 代理商： | HTSMOH5601EV |
HTSICH56_48_SDS
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product short data sheet
COMPANY PUBLIC
Rev. 3.0 — 12 October 2011
210330
7 of 21
NXP Semiconductors
HTSICH56; HTSICH48
HITAG S transponder IC
7.4 State Diagram
7.4.1
General Description of States
Power Off
The powering magnetic field is switched off or the HITAG S Transponder is out of field.
Ready
After start up phase, the HITAG S Transponder is ready to receive the first command.
Init
The HITAG S Transponder enters this State after the first UID REQUEST xx command. In
this State the Response Protocol Mode (see
Section 7.5
) may be changed by further
UID REQUEST xx commands. If there are several HITAG S Transponders in the field of
the RWD antenna at the same time, the AC SEQUENCE can be started to determine the
UID of every HITAG S Transponder.
Authenticate
The HITAG S Transponder enters this State after a valid SELECT (UID) command when
configured in Authentication Mode. After an encrypted CHALLENGE Authentication the
HITAG S Transponder changes into the Selected State.
Selected
The HITAG S Transponder enters this State after a valid SELECT (UID) command when
configured in Plain Mode or a SELECT (UID) and CHALLENGE sequence when
configured in Authentication Mode. Only one HITAG S Transponder in the field of the
RWD antenna can be Selected at the same time. In this State, Read and Write operations
are possible. Data Transmission is not encrypted even if configured in Authentication
Mode.
Quiet
The HITAG S Transponder enters this State after a SELECT_QUIET (UID) command in
Init State or a QUIET command in Selected State. In this State, the HITAG S Transponder
will not answer to any command. Switching off the powering magnetic field or moving the
HITAG S Transponder out of field enters it into the Power Off State.
Transponder Talks First (TTF)
The HITAG S Transponder enters this State when configured in TTF Mode if no
UID REQUEST xx command is received within the Mode switch window. Once entered
this State, the HITAG S Transponder continuously transmits data with configurable data
coding, data rate and data length.
相關PDF資料 |
PDF描述 |
|---|---|
| HUF75321P3 | 35A, 55V, 0.034 Ohm, N-Channel UltraFET Power MOSFETs(35A, 55V, 0.034 Ω, N溝道UltraFET功率MOS場效應管) |
| HUF75321S3S | 35A, 55V, 0.034 Ohm, N-Channel UltraFET Power MOSFETs(35A, 55V, 0.034 Ω, N溝道UltraFET功率MOS場效應管) |
| HUF75332G3 | 60A, 55V, 0.019 Ohm, N-Channel UltraFET Power MOSFETs |
| HUF75332P3 | 60A, 55V, 0.019 Ohm, N-Channel UltraFET Power MOSFETs |
| HUF75332S3S | 60A, 55V, 0.019 Ohm, N-Channel UltraFET Power MOSFETs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HTSMOH5601EV,118 | 功能描述:RFID應答器 HITAG S 256BIT MOA2 RoHS:否 制造商:Murata 存儲容量:512 bit 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| HTSMOH5601EV-T | 功能描述:RFID應答器 HITAG S 256BIT MOA2 MOD/REEL RoHS:否 制造商:Murata 存儲容量:512 bit 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| HTS-MV-B | 功能描述:散熱片 HEATSPREADER FOR Express-MV RoHS:否 制造商:Ampro By ADLINK 產品:Heat Sink Accessories 安裝風格:Through Hole 散熱片材料: 散熱片樣式: 熱阻: 長度: 寬度: 高度: 設計目的:Express-HRR |
| HTSNK P4-775 BTXR | 制造商:RadiSys 功能描述:HTSINK - LGA775 P4 BTX ROHS - Bulk |
| HTSN-M2.5-10-3 | 制造商:Richco 功能描述:STANDOFF THRD MALE/MALE BLK 10MM |
發布緊急采購，3分鐘左右您將得到回復。