- 您現在的位置：買賣IC網 > PDF目錄65467 > HMC292 (HITTITE MICROWAVE CORP) 18000 MHz - 32000 MHz RF/MICROWAVE DOUBLE BALANCED MIXER, 11 dB CONVERSION LOSS-MAX PDF資料下載
參數資料
| 型號： | HMC292 |
| 廠商： | HITTITE MICROWAVE CORP |
| 元件分類： | 混頻器 |
| 英文描述： | 18000 MHz - 32000 MHz RF/MICROWAVE DOUBLE BALANCED MIXER, 11 dB CONVERSION LOSS-MAX |
| 封裝： | 1.04 X 0.58 MM, 0.10 MM HEIGHT, MINIATURE, DIE-3 |
| 文件頁數： | 6/6頁 |
| 文件大?。?/td> | 207K |
| 代理商： | HMC292 |
M
IX
E
R
S
-
DO
UBL
E
-B
A
L
A
N
C
E
D
-
C
H
IP
4
4 - 47
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
Mounting & Bonding Techniques for Millimeterwave GaAs MMICs
The die should be attached directly to the ground plane eutectically or with
conductive epoxy (see HMC general Handling, Mounting, Bonding Note).
50 Ohm Microstrip transmission lines on 0.127mm (5 mil) thick alumina thin film
substrates are recommended for bringing RF to and from the chip (Figure 1). If
0.254mm (10 mil) thick alumina thin film substrates must be used, the die should
be raised 0.150mm (6 mils) so that the surface of the die is coplanar with the surface
of the substrate. One way to accomplish this is to attach the 0.102mm (4 mil) thick
die to a 0.150mm (6 mil) thick molybdenum heat spreader (moly-tab) which is then
attached to the ground plane (Figure 2).
Microstrip substrates should be brought as close to the die as possible in order to
minimize ribbon bond length. Typical die-to-substrate spacing is 0.076mm (3 mils).
Gold ribbon of 0.075 mm (3 mil) width and minimal length <0.31 mm (<12 mils) is
recommended to minimize inductance on RF, LO & IF ports.
Handling Precautions
Follow these precautions to avoid permanent damage.
Storage: All bare die are placed in either Waffle or Gel based ESD protective
containers, and then sealed in an ESD protective bag for shipment. Once the
sealed ESD protective bag has been opened, all die should be stored in a dry
nitrogen environment.
Cleanliness: Handle the chips in a clean environment. DO NOT attempt to clean
the chip using liquid cleaning systems.
Static Sensitivity: Follow ESD precautions to protect against ESD strikes.
Transients: Suppress instrument and bias supply transients while bias is applied.
Use shielded signal and bias cables to minimize inductive pick-up.
General Handling: Handle the chip along the edges with a vacuum collet or with
a sharp pair of bent tweezers. The surface of the chip has fragile air bridges and
should not be touched with vacuum collet, tweezers, or fingers.
Mounting
The chip is back-metallized and can be die mounted with AuSn eutectic preforms
or with electrically conductive epoxy. The mounting surface should be clean and flat.
Eutectic Die Attach: A 80/20 gold tin preform is recommended with a work surface temperature of 255 °C and a tool temperature
of 265 °C. When hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 °C. DO NOT expose the chip
to a temperature greater than 320 °C for more than 20 seconds. No more than 3 seconds of scrubbing should be required for
attachment.
Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed around the
perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule.
Wire Bonding
RF bonds made with 0.003” x 0.0005” ribbon are recommended. These bonds should be thermosonically bonded with a force of
40-60 grams. DC bonds of 0.001” (0.025 mm) diameter, thermosonically bonded, are recommended. Ball bonds should be made
with a force of 40-50 grams and wedge bonds at 18-22 grams. All bonds should be made with a nominal stage temperature of 150
°C. A minimum amount of ultrasonic energy should be applied to achieve reliable bonds. All bonds should be as short as possible,
less than 12 mils (0.31 mm).
0.102mm (0.004”) Thick GaAs MMIC
Wire Bond
RF Ground Plane
0.127mm (0.005”) Thick Alumina
Thin Film Substrate
0.076mm
(0.003”)
Figure 1.
0.102mm (0.004”) Thick GaAs MMIC
Wire Bond
RF Ground Plane
0.254mm (0.010”) Thick Alumina
Thin Film Substrate
0.076mm
(0.003”)
Figure 2.
0.150mm (0.005”) Thick
Moly Tab
HMC292
v06.1007
GaAs MMIC DOUBLE-BALANCED
MIXER, 18 - 32 GHz
相關PDF資料 |
PDF描述 |
|---|---|
| HMC304MS8 | 1700 MHz - 3000 MHz RF/MICROWAVE SINGLE BALANCED MIXER, 11 dB CONVERSION LOSS-MAX |
| HMC304MS8E | 1700 MHz - 3000 MHz RF/MICROWAVE SINGLE BALANCED MIXER, 11 dB CONVERSION LOSS-MAX |
| HMC311SC70 | 0 MHz - 8000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER |
| HMC311ST89E | 0 MHz - 6000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER |
| HMC313 | 0 MHz - 6000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HMC292_08 | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs MMIC DOUBLE-BALANCED MIXER, 18 - 32 GHz |
| HMC292_09 | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs MMIC DOUBLE-BALANCED MIXER, 18 - 32 GHz |
| HMC292ALC3B | 功能描述:IC MMIC MIXER HI IP3 12-QFN 制造商:analog devices inc. 系列:- 包裝:管件 零件狀態:在售 RF 類型:- 頻率:18GHz ~ 32GHz 混頻器數:1 增益:- 噪聲系數:9dB 輔助屬性:- 電流 - 電源:- 電壓 - 電源:- 封裝/外殼:12-CLCC 裸露焊盤 供應商器件封裝:12-CLCC（2.9x2.9） 標準包裝:1 |
| HMC292LC3B | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs MMIC FUNDAMENTAL MIXER, 16 - 30 GHz |
| HMC292LC3B_09 | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs MMIC FUNDAMENTAL MIXER, 16 - 30 GHz |
發布緊急采購，3分鐘左右您將得到回復。