- 您現在的位置：買賣IC網 > PDF目錄384420 > HIP1011E (Intersil Corporation) Dual Slot PCI Hot Plug Controller(雙電源分配控制器) PDF資料下載
參數資料
| 型號： | HIP1011E |
| 廠商： | Intersil Corporation |
| 英文描述： | Dual Slot PCI Hot Plug Controller(雙電源分配控制器) |
| 中文描述： | 雙插槽的PCI熱插拔控制器（雙電源分配控制器） |
| 文件頁數： | 11/15頁 |
| 文件大小： | 141K |
| 代理商： | HIP1011E |
11
Using the HIP1011DEVAL1 Platform
General and Biasing Information
The HIP1011DEVAL1 platform (Figure 24) comes as a three
part set consisting of 1 mother board emulator and 2 load
cards. This evaluation platform allows a designer to evaluate
and modify the performance and functionality of the
HIP1011D or HIP1011E in a simple environment.
Test point numbers (TP#) correspond to the HIP1011D/E
device (U5) pin numbers thus TP3 and TP12 are PWRON_2
and PWRON_1 respectively. These 2 pins are the
HIP1011D/E control inputs for each of the 2 integrated but
independent PCI power controllers in the HIP1011D/E.
On the HIP1011DEVAL1 platform are 4 HUF76132SK8,
(11.5m
, 30V, 11.5A) N-Channel power MOSFETs, (Q1-
Q4) these are used as the external switches for the +5V and
+3.3V supplies to the load card connectors, P1 and P2.
Current sensing is facilitated by the four 5m
1W metal strip
resistors (R1-R4), the voltages developed across the sense
resistors are compared to references on board the
HIP1011D/E.
The HIP1011DEVAL1 platform is powered through the J1 to
J5 connector jacks near the top of the board, see Table 2 for
bias voltage assignments.
After properly biasing the HIP1011D/E and ensuring there is
an adequate ground return from the HIP1011DEVAL1
platform to the power supplies, (otherwise anomalous and
unpredictable results will occur) signal the PWRON inputs
low then insert the load cards as shown in Figure 15.
Signaling either or both PWRON pins high (>2.4V) will turn
on the appropriate FET switches and apply voltage to the
load cards.
* The HIP1011DEVAL board is supplied with a HIP1011D
installed and in addition a loose packed HIP1011E.
Evaluating Time Delay to Latch-Off
Provided for delay to latch-off evaluation are 2 locations for
SMD capacitors, C7 and C8. Filling these locations places a
capacitor to ground from each of the HIP1011D/E FLTN pins
thus tailoring the FLTN signal going low ramp rate. This
provides a delay to the fault signal latch-off threshold
voltage, FLTN Vth. By increasing this time the HIP1011D
delays immediate latch-off of the bus supply switches, thus
ignoring transient OC and UV conditions. See Table 3
illustrating the time it takes for switch gate turn-off from the
FLTN start of response to an OC or UV condition. The FLTN
response to an OC or UV condition is 110ns. See Figures 20
through 23 for waveforms.
The intent of any protection device is to isolate the supply
quickly so a faulty card does not drag down a supply. A
longer latch-off delay results in less isolation from a faulty
card to supply.
TABLE 2. HIP1011DEVAL1 BIAS ASSIGNMENTS
J1
J2
J3
J4
J5
GND
+5V
-12V
+12V
+3.3V
LOAD CARDS
HIP1011D
FIGURE 15. CORRECT INSTALLATION OF LOAD CARDS
TABLE 3.
C7 AND C8 VALUE
OPEN
0.001
μ
F
0.01
μ
F
0.1
μ
F
FLTN to Gate Response
0.1
μ
s
0.44
μ
s
2.9
μ
s
28
μ
s
3V5VG
FLTN
FLTN, Vth
FIGURE 16. TIMING DIAGRAM
1ns
10ns
100ns
1
μ
s
10
μ
s
100
μ
s
1ms
10ms
0.001
μ
F
0.1
μ
F
1
μ
F
10
μ
F
OPEN
0.01
μ
F
FIGURE 17. TYPICAL OC/UV TO VG RESPONSE vs FLTN CAP
HIP1011D, HIP1011E
相關PDF資料 |
PDF描述 |
|---|---|
| HIP1020 | Single, Double or Triple-Output Hot Plug Controller(單/雙或三輸出帶電插拔控制器) |
| HIP1031 | 20000 SYSTEM GATE LOGIC CELL ARRAY - NOT RECOMMENDED for NEW DESIGN |
| HIP1031AS | 20000 SYSTEM GATE LOGIC CELL ARRAY - NOT RECOMMENDED for NEW DESIGN |
| HIP1090 | Protected High Side Power Switch with Transient Suppression |
| HIP1090AS | 20000 SYSTEM GATE LOGIC CELL ARRAY - NOT RECOMMENDED for NEW DESIGN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HIP1011ECA | 功能描述:IC CTRLR HOTPLUG DUAL 28-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| HIP1011ECA-T | 功能描述:IC CTRLR HOTPLUG DUAL 28-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| HIP1011ECAZA | 功能描述:熱插拔功率分布 W/ANNEAL DL VER HIP1 W/OUT UV FUN RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| HIP1011ECAZA-T | 功能描述:熱插拔功率分布 W/ANNEAL DL VER HIP1 W/OUT UV FUN RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| HIP1011EVAL1 | 功能描述:電源管理IC開發工具 PCI HOT PLUG EVALUATION BRD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。