- 您現在的位置：買賣IC網 > PDF目錄370568 > HEDS-9140 Three Channel Optical Incremental Encoder Modules PDF資料下載
參數資料
| 型號： | HEDS-9140 |
| 英文描述： | Three Channel Optical Incremental Encoder Modules |
| 中文描述： | 三通道光學增量編碼器模塊 |
| 文件頁數： | 7/12頁 |
| 文件大?。?/td> | 307K |
| 代理商： | HEDS-9140 |
7
Instructions:
1. Place codewheel on shaft.
2. Set codewheel height by
placing alignment tool on motor
base (pins facing up) flush up
against the codewheel as shown
in Figure 3. Tighten codewheel
setscrew and remove alignment
tool.
3. Insert mounting screws
through module and thread into
the motor base. Do not tighten
screws.
4. Slide alignment tool over
codewheel hub and onto module
as shown in Figure 4. The pins of
the alignment tool should fit
snugly inside the alignment
recesses of the module.
Mounting with an
Alignment Tool
The HEDS-8905 and HEDS-8906
alignment tools are recommended
for mounting the modules with
Side B as the mounting plane. The
HEDS-8905 is used to mount the
HEDS-9140, and the HEDS-8906
is used to mount the HEDS-9040.
These tools fix the module
position using the codewheel hub
as a reference. They will not work
if Side A is used as the mounting
plane.
The following assembly procedure
uses the HEDS-8905/8906
alignment tool to mount a HEDS-
9140/9040 module and a HEDS-
5140/6140 codewheel:
5. While holding alignment tool in
place, tighten screws down to
secure module.
6. Remove alignment tool.
Mounting with Aligning
Pins
The HEDS-9040 and HEDS-9140
can also be mounted using
aligning pins on the motor base.
(Hewlett-Packard does not
provide aligning pins.) For this
configuration, Side A must be
used as the mounting plane. The
aligning recess centers must be
located within the 0.005 in. R
Tolerance Circle as explained
above. Figure 5 shows the
necessary dimensions.
Figure 3. Alignment Tool is Used to Set Height of
Codewheel.
Figure 4. Alignment Tool is Placed over Shaft and onto
Codewheel Hub. Alignment Tool Pins Mate with Aligning
Recesses on Module.
MODULE SIDE A
MODULE
SIDE B
ARTWORK SIDE
MOTOR
BOSS
CODE
WHEEL
BOSS
MOTOR
相關PDF資料 |
PDF描述 |
|---|---|
| HEDS-9040B06 | Three Channel Optical Incremental Encoder Modules |
| HEDS-9040B08 | Three Channel Optical Incremental Encoder Modules |
| HEDS-9040B09 | Three Channel Optical Incremental Encoder Modules |
| HEDS-9040B10 | Three Channel Optical Incremental Encoder Modules |
| HEDS-9040B11 | Three Channel Optical Incremental Encoder Modules |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HEDS-9140#100 | 制造商:Hewlett Packard Co 功能描述: |
| HEDS-9140#A00 | 功能描述:編碼器 3 Channel 500CPR RoHS:否 制造商:Avago Technologies 產品:Optical Encoders 類型:Absolute 每轉脈沖: 制動器數量: 通道數量:2 安裝風格:Through Hole 端接類型:Solder Pin 輸出: 軸類型: 帶開關: 電源電壓:5 V 工作溫度范圍:- 40 C to + 115 C |
| HEDS-9140#A00 | 制造商:Avago Technologies 功能描述:Incremental Encoder |
| HEDS-9140#C00 | 功能描述:編碼器 3 Channel 100CPR RoHS:否 制造商:Avago Technologies 產品:Optical Encoders 類型:Absolute 每轉脈沖: 制動器數量: 通道數量:2 安裝風格:Through Hole 端接類型:Solder Pin 輸出: 軸類型: 帶開關: 電源電壓:5 V 工作溫度范圍:- 40 C to + 115 C |
| HEDS-9140#E00 | 功能描述:編碼器 3 Channel 200CPR RoHS:否 制造商:Avago Technologies 產品:Optical Encoders 類型:Absolute 每轉脈沖: 制動器數量: 通道數量:2 安裝風格:Through Hole 端接類型:Solder Pin 輸出: 軸類型: 帶開關: 電源電壓:5 V 工作溫度范圍:- 40 C to + 115 C |
發布緊急采購，3分鐘左右您將得到回復。