參數資料
型號： HDM8513A
廠商： Hynix Semiconductor Inc.
元件分類： 基準電壓源/電流源
英文描述： Linear Voltage Regulator IC; Package/Case:3-TO-92; Supply Voltage:30V; Output Voltage:5V; Current Rating:0.1A; Operating Temp. Max:70 C; Operating Temp. Min:0 C; Output Voltage Max:5V; Voltage Regulator Type:Positive Voltage
中文描述： 的DVB /決策支持系統兼容接收器
文件頁數： 39/67頁
文件大?。?/td> 261K
代理商： HDM8513A
39
5.3 Monitor and Control Interface
Three different modes are supported for the monitor and control interface. Two of the modes are 8
bit parallel interfaces, one which supports Intel microcontrollers and the other intended for Motorola
microcontrollers. The third mode is a serial interface conforming to the I2C standard.
The I2C mode is activated by placing BUSMODE high at the same time both /RE and /WE are low
simultaneously. When this mode is active, the seven bit I2C slave address of the HDM8513A is
configured by the seven least significant bits of the HI_DATA[7:0] bus.
HI_DATA [7:0]
This bi-directional data bus is used for transferring control parameters to
the demodulator and for reading the status registers within the
demodulator.
/CE
Chip enable is an active low input to the demodulator which signifies that
the other control signals are active.
/RE
Read Enable is an active low input to the device which, when active at the
same time chip enable is true, permits the device to drive the HI_DATA
[7:0] lines. When BUSMODE is 0 (Motorola), this pin is read / not write
(see timing diagrams).
/WE
Write enable is an active low input to the device which, when true at the
same time chip enable is true, causes input data on the HI_DATA [7:0] bus
to be transferred to the register defined by the HI_ADDR [4:0] bus. When
BUSMODE is 0 (Motorola), this pin is not data strobe (see timing
diagrams).
HI_ADDR [4:0]
The address bus defines which location within the device is to be accessed
during a read or write operation.
BUSMODE
chip. When high, an Intel processor/microcontroller interface is used.
When low, a Motorola processor interface is used.
DTACK
the HDM8513A.
SCL_I2C
SDA_I2C
This pin is the data for the I2C interface and requires an external pull-up
resistor as per the I2C standard.
SDA_I2CO
This pin, which can be by-passed, is the data for the I2C interface.
SCL_I2CO
This pin, which can be by-passed, provides the clock for the I2C interface.
BUSMODE selects the type of microcontroller/processor used to setup the
Data Acknowledge/Data Ready is a tristate output signal which informs
the controlling processor that a data transfer has been acknowledged by
This pin provides the clock for the I2C interface when that mode is active.
相關PDF資料
PDF描述
HDM8513AP Timer IC; Supply Voltage Max:16V; Package/Case:14-DIP; Current Rating:10A; Timer Type:Timer-Dual; Mounting Type:Through Hole
HDM8513AT Darlington Bipolar Transistor; Power Dissipation:175W; Package/Case:TO-3; Mounting Type:Through Hole; Current Rating:20A; Voltage Rating:500V
HDM8515 ANALOG IC - DATASHEET REFERENCE
HDM8515P Operational Amplifier (Op-Amp) IC; Number of Amplifiers:4; Package/Case:14-DIP; Op Amp Type:Low Power; Single Supply Voltage Min (+V):3V; Dual Supply Voltage Max (+/- V):16V; Amplifier Type:Operational; Mounting Type:Through Hole
HE6SF200 High efficiency super fast silicon rectifier diode
相關代理商/技術參數
參數描述
HDM8513AP 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:DVB/DSS Compliant Receiver
HDM8513AT 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:DVB/DSS Compliant Receiver
HDM8515 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:DVB/DSS Compliant Receiver
HDM8515P 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:DVB/DSS Compliant Receiver
HDM9010 制造商:SHOULDER 制造商全稱:SHOULDER 功能描述:Frequency Synthesizer
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*