參數資料
型號： HA9P5320-5Z
廠商： INTERSIL CORP
元件分類： 運動控制電子
英文描述： 1 Microsecond Precision Sample and Hold Amplifier
中文描述： SAMPLE AND HOLD AMPLIFIER, 1 us ACQUISITION TIME, PDSO16
封裝： SOIC-16
文件頁數： 5/8頁
文件大小： 239K
代理商： HA9P5320-5Z
5
FN2857.7
August 24, 2005
Application Information
The HA-5320 has the uncommitted differential inputs of an
op amp, allowing the Sample and Hold function to be
combined with many conventional op amp circuits. See the
Intersil Application Note AN517 for a collection of circuit
ideas.
Layout
A printed circuit board with ground plane is recommended
for best performance. Bypass capacitors (0.01
μ
F to 0.1
μ
F,
ceramic) should be provided from each power supply
terminal to the Supply Ground terminal on pin 13.
The ideal ground connections are pin 6 (SIG. Ground)
directly to the system Signal Ground, and pin 13 (Supply
Ground) directly to the system Supply Common.
Hold Capacitor
The HA-5320 includes a 100pF MOS hold capacitor,
sufficient for most high speed applications (the Electrical
Specifications section is based on this internal capacitor).
Additional capacitance may be added between pins 7 and
11. This external hold capacitance will reduce droop rate at
the expense of acquisition time, and provide other trade-offs
as shown in the Performance Curves.
If an external hold capacitor C
EXT
is used, then a noise
bandwidth capacitor of value 0.1C
EXT
should be connected
from pin 8 to ground. Exact value and type are not critical.
The hold capacitor C
EXT
should have high insulation
resistance and low dielectric absorption, to minimize droop
errors. Polystyrene dielectric is a good choice for operating
temperatures up to 85°C. Teflon and glass dielectrics offer
good performance to 125°C and above.
Test Circuits and Waveforms
FIGURE 1. CHARGE TRANSFER AND DRIFT CURRENT
FIGURE 2. CHARGE TRANSFER TEST
FIGURE 3. DRIFT CURRENT TEST
FIGURE 4. HOLD MODE FEEDTHROUGH ATTENUATION
14
2
1
7
8
11
NC
NC
-INPUT
+INPUT
S/H CONTROL
CONTROL
INPUT
S/H
OUTPUT
V
O
(C
H
= 100pF)
HA-5320
S/H CONTROL
V
O
V
P
HOLD (+3.5V)
SAMPLE (0V)
NOTES:
13. Observe the “hold step” voltage V
P
.
14. Compute charge transfer: Q = V
P
C
H
.
S/H CONTROL
V
O
V
O
t
NOTES:
15. Observe the voltage “droop”,
V
O
/
t.
16. Measure the slope of the output during hold,
V
O
/
t, and
compute drift current: I
D
= C
H
V
O
/
t.
HOLD (+3.5V)
SAMPLE (0V)
VIN
ANALOG
MUX OR
SWITCH
A
IN
S/H CONTROL
SUPPLY
GND
+IN
-IN
OUT
V
OUT
7
1
2
14
V-
V+
S/H CONTROL
INPUT
9
5
100kHz
SINE WAVE
10V
C
EXT
TO
SIGNAL
GND
TO
SUPPLY
COMMON
NC
13
11
6
NC
8
INT.
COMP.
REF
COM
HA-5320
NOTE:
Feedthrough in
where:
V
OUT
= V
P-P
, Hold Mode, V
IN
= V
P-P
.
dB
20
V
IN
--------------
log
=
HA-5320
相關PDF資料
PDF描述
HA9P5320-9 1 Microsecond Precision Sample and Hold Amplifier
HA-5320 ECONOLINE: RxxP2xx - EN 60950 certified, rated for 250VAC - UL-60950-1 / CSA C22.2 certified - 5.2kVDC Isolation for 1 Minute - Optional Continuous Short Circuit Protected - Wide Operating Temperature Range at full 2 Watts Load, .40?????C to +85?????C - Twin Chamber Transform
HA9P5320-5 1 Microsecond Precision Sample and Hold Amplifier
HA-5320883 High Speed Precision Sample and Hold Amplifier
HA3-5320-5 1 Microsecond Precision Sample and Hold Amplifier
相關代理商/技術參數
參數描述
HA9P5320-5ZX96 功能描述:采樣&保持放大器 Pb-Free w/Anneal SMP&HLD 2MHZ 1US INTCAP 16WSOIC COM, T&R RoHS:否 制造商:Texas Instruments 通道數量:2 捕獲時間:20 us 電源電壓-最大:18 V 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 安裝風格: 封裝 / 箱體:SOIC-14 封裝:Tube
HA9P5320-9 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:1 Microsecond Precision Sample and Hold Amplifier
HA9P5340-5 制造商:Rochester Electronics LLC 功能描述:SMP&HLD 10MHZ 700NS INTCAP 16WSOIC COM - Bulk
HA9P7712B-5 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Feedback Operational Amplifier
HA9P7712B-9 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Feedback Operational Amplifier
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*