- 您現在的位置：買賣IC網 > PDF目錄384385 > HA4314BCB (HARRIS SEMICONDUCTOR) 400MHz, 4 x 1 Video Crosspoint Switch PDF資料下載
參數資料
| 型號： | HA4314BCB |
| 廠商： | HARRIS SEMICONDUCTOR |
| 元件分類： | 運動控制電子 |
| 英文描述： | 400MHz, 4 x 1 Video Crosspoint Switch |
| 中文描述： | 4-CHANNEL, CROSS POINT SWITCH, PDSO14 |
| 文件頁數： | 4/10頁 |
| 文件大?。?/td> | 127K |
| 代理商： | HA4314BCB |
4
capacitance, C
L
, driven. Bandwidth and slew rate degrade
as C
L
increases (as shown in the Electrical Specification
table), so give careful consideration to component
placement to minimize trace length. In big matrix
configurations where C
L
is large, better frequency response
is obtained by cascading two levels of crosspoints in the
case of multiplexed outputs (see Figure 2), or distributing the
load between two drivers if C
L
is due to bussing and
subsequent stage input capacitance.
Control Signals
CS - This is a TTL/CMOS compatible, active low Chip Select
input. When driven high, CS forces the output to a true high
impedance state and reduces the power dissipation by a
factor of 25. The CS input has no on-chip pull-down resistor,
so it must be connected to a logic low (recommend GND) if
the enable function isn’t utilized.
A0, A1 - These are binary coded, TTL/CMOS compatible
address inputs that select which one of the four inputs
connect to the crosspoint output.
Switcher/Router Applications
Figure 1 illustrates one possible implementation of a
wideband, low power, 4 x 4 switcher/router utilizing the
HA4314B for the switch matrix. A 4 x 4 switcher/router allows
any of the four outputs to be driven by any one of the four
inputs (e.g., each of the four inputs may connect to a
different output, or an input may connect to multiple outputs).
This application utilizes the HA4600 (video buffer with output
disable) for the input buffer, the HA4314B as the switch
matrix, and the HFA1112 (programmable gain buffer) as the
gain of two output driver. Figure 2 details a 16 x 1 switcher
(basically a 16:1 mux) which uses the HA4201 (1 x 1
crosspoint) and the HA4314B in a cascaded stage
configuration to minimize capacitive loading at each output
node, thus increasing system bandwidth.
Power Up Considerations
No signals should be applied to the analog or digital inputs
before the power supplies are activated. Latch-up may occur
if the inputs are driven at the time of power up. To prevent
latch-up, the input currents during power up must not exceed
the values listed in the Absolute Maximum Ratings.
Intersil’s Crosspoint Family
Intersil offers a variety of 4 x 1 and 1 x 1 crosspoint switches.
In addition to the HA4314B, the 4 x 1 family includes the
HA4404 and HA4344. The HA4404 is a 16 lead device with
Tally outputs to indicate the selected channel. The HA4344
is a 16 lead crosspoint with synchronized control lines (A0,
A1, CS). With synchronization, the control information for the
next channel switch can be loaded into the crosspoint
without affecting the current state. On a subsequent clock
edge the stored control state effects the desired channel
switch.
The 1 x 1 family is comprised of the HA4201 and HA4600.
They are essentially similar devices, but the HA4201
includes a Tally output (enable indicator). The 1 x 1s are
useful as high performance video input buffers, or in a switch
matrix requiring very high off isolation.
+
-
SOURCE 0
75
OUT
SOURCE 1
SOURCE 2
SOURCE 3
75
75
75
HA4314
OUT
CS
IN3
IN0
HA4600
HA4600
EN
OUT
EN
X2
R
S
R
S
75
OUT0
R
S
HA4314
OUT
CS
IN3
IN0
X2
R
S
75
OUT1
HA4314
OUT
CS
IN3
IN0
X2
R
S
75
OUT2
HA4314
OUT
CS
IN3
IN0
X2
R
S
75
OUT3
OUTPUT BUFFERS
(HFA1112 OR HFA1115)
INPUT BUFFERS
+5V
SWITCH MATRIX
+5V
+
-
+
-
+
-
FIGURE 1. 4 x 4 SWITCHER/ROUTER APPLICATION
HA4314B
相關PDF資料 |
PDF描述 |
|---|---|
| HA4314BCP | 400MHz, 4 x 1 Video Crosspoint Switch |
| HA4314BCA | 400MHz, 4 x 1 Video Crosspoint Switch |
| HA4314BCA96 | 400MHz, 4 x 1 Video Crosspoint Switch |
| HA4314BCB96 | 400MHz, 4 x 1 Video Crosspoint Switch |
| HA4314B | 400MHz, 4x1 Video Crosspoint Switch(400MHz,4x1 視頻矩陣開關) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HA4314BCB96 | 功能描述:IC VIDEO CROSSPOINT SWIT 14SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 標準包裝:48 系列:- 功能:開關 電路:4 x SPST - NO 導通狀態電阻:100 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:管件 |
| HA4314BCBZ | 功能描述:模擬和數字交叉點 IC MUX 4:1 VID 14LD COM RoHS:否 制造商:Micrel 配置:2 x 2 封裝 / 箱體:MLF-16 數據速率:10.7 Gbps 輸入電平:CML, LVDS, LVPECL 輸出電平:CML 電源電壓-最大:3.6 V 電源電壓-最小:2.375 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 產品:Digital Crosspoint 封裝:Tube |
| HA4314BCBZ | 制造商:Intersil Corporation 功能描述:Multiplexer IC |
| HA4314BCBZ96 | 功能描述:模擬和數字交叉點 IC MUX 4:1 VID 14LD COM RoHS:否 制造商:Micrel 配置:2 x 2 封裝 / 箱體:MLF-16 數據速率:10.7 Gbps 輸入電平:CML, LVDS, LVPECL 輸出電平:CML 電源電壓-最大:3.6 V 電源電壓-最小:2.375 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 產品:Digital Crosspoint 封裝:Tube |
| HA4314BCP | 功能描述:IC VIDEO CROSSPOINT SWITCH 14DIP RoHS:否 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 標準包裝:48 系列:- 功能:開關 電路:4 x SPST - NO 導通狀態電阻:100 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。