- 您現在的位置：買賣IC網 > PDF目錄362744 > EPC16QI100 (Altera Corporation) 2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet PDF資料下載
參數資料
| 型號： | EPC16QI100 |
| 廠商： | Altera Corporation |
| 英文描述： | 2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet |
| 中文描述： | 2。增強型配置器件（EPC4，EPC8 |
| 文件頁數： | 25/36頁 |
| 文件大?。?/td> | 421K |
| 代理商： | EPC16QI100 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
Altera Corporation
August 2005
2–25
Configuration Handbook, Volume 2
Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet
The enhanced configuration device supports a programmable POR delay
setting. You can set the POR delay to the default 100-ms setting or reduce
the POR delay to 2 ms for systems that require fast power-up. The
PORSEL
input pin controls this POR delay; a logic high level selects the
2-ms delay, while a logic low level selects the 100-ms delay.
The enhanced configuration device can enter reset under the following
conditions:
■
The POR reset starts at initial power-up during V
CC
ramp-up or if
V
CC
drops below the minimum operating condition anytime after
V
CC
has stabilized
The FPGA initiates reconfiguration by driving
nSTATUS
low, which
occurs if the FPGA detects a CRC error or if the FPGA’s
nCONFIG
input pin is asserted
The controller detects a configuration error and asserts
OE
to initiate
re-configuration of the Altera FPGA (for example when
CONF_DONE
stays low after all configuration data has been transmitted)
■
■
Power
Sequencing
Altera requires that you power-up the FPGA's V
CCINT
supply before the
enhanced configuration device's POR expires.
Power up needs to be controlled so that the enhanced configuration
device’s
OE
signal goes high after the
CONF_DONE
signal is pulled low. If
the EEPC device exits POR before the FPGA is powered up, the
CONF_DONE
signal will be high since the pull-up resistor is holding this
signal high. When the enhanced configuration device exits POR,
OE
is
released and pulled high by a pull-up resistor. Since the enhanced
configuration device samples the
nCS
signal on the rising edge of
OE
, it
detects a high level on
CONF_DONE
and enters an idle mode.
DATA
and
DCLK
outputs will not toggle in this state and configuration will not
begin. The enhanced configuration device will only exit this mode if it is
powered down and then powered up correctly.
1
To ensure the enhanced configuration device enters
configuration mode properly, you need to ensure that the FPGA
completes power-up before the enhanced configuration device
exits POR.
The pin-selectable POR time feature is useful for ensuring this power-up
sequence. The enhanced configuration device has two POR settings, 2 ms
when
PORSEL
is set to a high level and 100 ms when
PORSEL
is set to a
low level. For more margin, the 100-ms setting can be selected to allow the
FPGA to power-up before configuration is attempted.
相關PDF資料 |
PDF描述 |
|---|---|
| EPC8xxx | 2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet |
| EPC8QC100 | 2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet |
| EPC8QI100 | 2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet |
| EPC16xxx | 435882001 |
| EPC4QC100 | 2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EPC16QI100N | 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 16Mb 33 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20 |
| EPC16UC88 | 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 16Mb 33 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20 |
| EPC16UC88AA | 功能描述:IC CONFIG DEVICE 16MBIT 88-UBGA RoHS:否 類別:集成電路 (IC) >> 存儲器 - 用于 FPGA 的配置 Proms 系列:EPC 產品變化通告:Product Discontinuation 28/Jul/2010 標準包裝:98 系列:- 可編程類型:OTP 存儲容量:300kb 電源電壓:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-TSOP 包裝:管件 |
| EPC16UC88N | 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 16Mb 33 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20 |
| EPC16UI88AA | 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 16Mb 33 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20 |
發布緊急采購，3分鐘左右您將得到回復。