- 您現在的位置：買賣IC網 > PDF目錄362686 > EM78M612CDP (ELAN Microelctronics Corp .) High-Performance, Single-Ended, Current-Mode PWM Controllers PDF資料下載
參數資料
| 型號： | EM78M612CDP |
| 廠商： | ELAN Microelctronics Corp . |
| 英文描述： | High-Performance, Single-Ended, Current-Mode PWM Controllers |
| 中文描述： | 通用串行總線控制器系列 |
| 文件頁數： | 26/38頁 |
| 文件大?。?/td> | 1264K |
| 代理商： | EM78M612CDP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
EM78M612
Universal Serial Bus Microcontroller Series
This specification may change without further notice
.
2004/4/28 V1.1
26
8.3.2 Wakeup by Port Change Function
Each of the GPIO pins in Port 6 and Port 7 can wakeup the MCU through signal change
from input pin. This function is used to wake-up the MCU automatically from sleep mode. It
also supports the remote wake-up function for USB application.
Any of the Individual pins of Port 6 and Port 7 can be defined to wakeup the MCU by setting
their respective bits, R8 and R9.
8.4 USB Application
EM78M612 is specially designed for USB device application and has many powerful
functions that help the firmware to free itself from complex situation in various aspects of
USB application.
8.4.1 Auto-Detect PS/2 or USB Mode
When the EM78M612 is connected to the bus, it will auto-detect and identify which type of
bus (USB or PS/2) it is connected to. The conditions that influence auto-detect function are
described below
:
1. After a Power-on reset, the initial value of IOCA [0,1] is 0b00. Thus the operation
mode is “Detect mode” and the D+ and D- I/O pins are internal pulled high by 200K
Ohm to V
DD
.
2. The firmware checks the state of R5 [0,1]. If the state with which these two bits is
0x00, set the IOCA [0] to “1” to define the “USB mode.” Otherwise, set the IOCA [1]
to “1,” to define “PS/2 mode.”
3. When the operation mode is defined as “USB mode,” the D- I/O pin is internal pulled
high by a 1.5K Ohm resistor to 3.3V, which is output from a built-in regulator.
4. If the operation mode is in “PS/2 mode,” both of the PS/2 interface I/O pins are
internal pulled high by a 4.7K Ohm resistor to V
DD
.
{NOTE]
If the auto-detect function is not used, the firmware should set the operation mode,
either in USB mode or PS/2 mode, at the beginning of program.
An additional mode, “USB Test Mode” is also available. This mode has no load on D+ and
D- I/O pins, and can only be used in USB Application case. Therefore, an external 1.5K Ohm
resistor is needed to pull up D- I/O pin to 3.3V.
Under “PS/2 mode,” both PS/2 pins are programmed to generate an interrupt. After setting
the Port 5 State change to Interrupt Enable bit, the MCU will interrupt while the state of these
two pins changes.
相關PDF資料 |
PDF描述 |
|---|---|
| EM78M612CEM | Universal Serial Bus Microcontroller Series |
| EM78M612D | High-Performance, Single-Ended, Current-Mode PWM Controllers |
| EM78M612ABM | Universal Serial Bus Microcontroller Series |
| EM78M612ABP | Universal Serial Bus Microcontroller Series |
| EM78M612ACM | Universal Serial Bus Microcontroller Series |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EM78M612CEM | 制造商:EMC 制造商全稱:ELAN Microelectronics Corp 功能描述:Universal Serial Bus Microcontroller Series |
| EM78M612CFM | 制造商:EMC 制造商全稱:ELAN Microelectronics Corp 功能描述:Universal Serial Bus Microcontroller Series |
| EM78M612D | 制造商:EMC 制造商全稱:ELAN Microelectronics Corp 功能描述:Universal Serial Bus Microcontroller Series |
| EM78M612DAM | 制造商:EMC 制造商全稱:ELAN Microelectronics Corp 功能描述:Universal Serial Bus Microcontroller Series |
| EM78M612DAP | 制造商:EMC 制造商全稱:ELAN Microelectronics Corp 功能描述:Universal Serial Bus Microcontroller Series |
發布緊急采購，3分鐘左右您將得到回復。