- 您現在的位置：買賣IC網 > PDF目錄362686 > EM78M612AAP (ELAN Microelctronics Corp .) Universal Serial Bus Microcontroller Series PDF資料下載
參數資料
| 型號： | EM78M612AAP |
| 廠商： | ELAN Microelctronics Corp . |
| 英文描述： | Universal Serial Bus Microcontroller Series |
| 中文描述： | 通用串行總線控制器系列 |
| 文件頁數： | 29/38頁 |
| 文件大?。?/td> | 1264K |
| 代理商： | EM78M612AAP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
EM78M612
Universal Serial Bus Microcontroller Series
This specification may change without further notice
.
2004/4/28 V1.1
29
The USB Host Resume Interrupt can only be used in this mode. If this interrupt is enabled,
the MCU will be interrupted when the USB Suspend signal is detected on USB Bus.
8.7 Interrupt
The EM78M612 has two interrupt vectors, one is in 0x0001, and the other is in 0x000A.
When an interrupt occurs while the MCU is running, it will jump to the interrupt vector
(0x0001 or 0x000A) and execute the instructions sequentially from interrupt vector. RF is the
interrupt status register that records the interrupt status in the relative flags/bits.
The interrupt condition could be one of the following
:
1. TCC Overflow
When the Timer Clock / Counter Register (R1) overflows, the
status flag RF[0] will be set to 1. Its interrupt vector is 0X0001.
2. EP0 Interrupt
When the UDC successfully received a setup transaction from
host to EndPoint0, the status flag RF[1] will be set to 1. Its
interrupt vector is 0X000A.
3. USB Suspend
When UDC detects a USB Suspend signal on USB bus, the
status flag RF[2] will be set to 1. Its interrupt vector is 0X000A.
4. USB Reset
When the UDC detects a USB Reset signal on USB bus, the
status flag RF[3] will be set to 1. Its interrupt vector is 0X000A.
5. USB Host Resume
When UDC detects that the USB bus has left the Suspend
condition, the status flag RF[4] will be set to 1. Its interrupt vector
is 0X000A.
6. Port 5 State Change
When the input signals in Port 5 changes, the status flag RF[5]
will be set to 1. Its interrupt vector is 0X0001.
7. High Pattern Detecting Interrupt Conditions If the Pattern Detecting Application function
is enabled, there will be three conditions with which interruption is
generated, and the status flag RF[6] is set to 1, Its interrupt vector
is 0X0001.
a) P.60 turns to low, and the Pattern Counter value bigger than
RA register value.
b) P.60 stays at high, and Pattern Counter value equal 0XFF.
c) P.60 turns to low and Pattern Counter value bigger than
0XFF.
相關PDF資料 |
PDF描述 |
|---|---|
| EM78M612DAM | Universal Serial Bus Microcontroller Series |
| EM78M612DAP | Universal Serial Bus Microcontroller Series |
| EM78M612DBM | Universal Serial Bus Microcontroller Series |
| EM78M612DBP | Universal Serial Bus Microcontroller Series |
| EM78M612DCM | CABLE ASSEMBLY; SMA MALE TO SMA FEMALE BULKHEAD; 50 OHM, RG178B/U COAX; 36" CABLE LENGTH; |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EM78M612ABM | 制造商:EMC 制造商全稱:ELAN Microelectronics Corp 功能描述:Universal Serial Bus Microcontroller Series |
| EM78M612ABP | 制造商:EMC 制造商全稱:ELAN Microelectronics Corp 功能描述:Universal Serial Bus Microcontroller Series |
| EM78M612ACM | 制造商:EMC 制造商全稱:ELAN Microelectronics Corp 功能描述:Universal Serial Bus Microcontroller Series |
| EM78M612ACP | 制造商:EMC 制造商全稱:ELAN Microelectronics Corp 功能描述:Universal Serial Bus Microcontroller Series |
| EM78M612ADM | 制造商:EMC 制造商全稱:ELAN Microelectronics Corp 功能描述:Universal Serial Bus Microcontroller Series |
發布緊急采購，3分鐘左右您將得到回復。