參數資料
型號： EM6604DL24A
英文描述： Microcontroller
中文描述： 微控制器
文件頁數： 35/39頁
文件大?。?/td> 675K
代理商： EM6604DL24A
EM6603
03/02 REV. G/439
Copyright
2002, EM Microelectronic-Marin SA
5
www.emmicroelectronic.com
1
Operating modes
The EM6603 has two low power dissipation modes:
STANDBY and SLEEP. Figure 4 is a transition
diagram for these modes.
1.1 STANDBY Mode
Executing a HALT instruction puts the EM6603 into
STANDBY mode. The voltage regulator, oscillator,
Watchdog timer, interrupts and timer/event counter are
operating. However, the CPU stops since the clock
related to instruction execution stops. Registers, RAM,
and I/O pins retain their states prior to STANDBY
mode. STANDBY is cancelled by a RESET or an
Interrupt request if enabled.
1.2 SLEEP MODE
Writing to the SLEEP* bit in the IntRq* register puts
the EM6603 in SLEEP mode. The oscillator stops and
most functions of the EM6603 are inactive. To be able
to write the SLEEP bit, the SLmask bit must first be
set to 1. In SLEEP mode only the voltage regulator
and RESET input are active. The RAM data integrity is
maintained. SLEEP mode may be cancelled only by a
RESET at the terminal pin of the EM6603. The RESET
must be high for at least 2sec.
Figure 4.Mode Transition diagram
Table 2 : shows the state of the EM6603 functions in
STANDBY and SLEEP modes.
Table 2.StandBy and Sleep Activities
FUNCTION
STANDBY SLEEP
Oscillator
Active
Stopped
Instruction Execution Stopped
Stopped
Registers and Flags
Retained
Reset
Interrupt Functions
Active
Stopped
RAM
Retained
Timer/Counter
Active
Stopped
Watchdog
Active
Stopped
I/O pins
Active
High-Z or
Retained
Supply VLD
Stopped
Reset pin
Active
Due to the cold start characteristics of the oscillator, waking up from SLEEP mode may take some time to
guarantee that the oscillator has started correctly. During this time the circuit is in RESET and the strobe output
STB/RST is high. Waking up from SLEEP mode clears the SLEEP flag but not the SLmask bit. By reading
SLmask one can therefore determine if the EM6603 was powered up (SLmask = 0), or woken from SLEEP mode
(SLmask = 1).
2
Power Supply
The EM6603 is supplied by a single external power supply between Vdd and Vss, the circuit reference being at
Vss (ground). A built-in voltage regulator generates Vreg providing regulated voltage for the oscillator and internal
logic. Output drivers are supplied directly from the external supply Vdd. A typical connection configuration is shown
in Figure 3.
For Vdd less then 1.4V it is recommended that Vdd is connected directly to Vreg
For Vdd>1.8V then the configuration shown in Fig.3 should be used.
*registers are marked in bold and underlined like
IntRq
*Bits/Flags in registers are marked in bold only like
SLEEP
相關PDF資料
PDF描述
EM6604SO24A Microcontroller
EM6604SO24B Microcontroller
EM6604TP24B Microcontroller
EM6605DL24A Microcontroller
EM6605SO24A Microcontroller
相關代理商/技術參數
參數描述
EM6604SO24A 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller
EM6604SO24B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller
EM6604TP24B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller
EM6604WP11 制造商:EMMICRO 制造商全稱:EM Microelectronic - MARIN SA 功能描述:Ultra Low Power Multi I/O Microcontroller
EM6604WP27 制造商:EMMICRO 制造商全稱:EM Microelectronic - MARIN SA 功能描述:Ultra Low Power Multi I/O Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*