| 品牌 | 登發牌 | 型號 | 12p |
| 應用范圍 | 汽車 | 種類 | 板對板 |
| 接口類型 | 汽車音響 | 支持卡數 | 二合一 |
| 讀卡類型 | cf | 形狀 | 條形 |
| 工藝 | 熔接 | 特性 | 防潮 |
| 接觸件材質 | 磷青銅、鈹銅 | 絕緣體材質 | 無 |
| 芯數 | 無 | 針數 | n |
| 線長 | 無（mm） |
本公司汽車連接器、fpc扁平電纜連接器、條形連接器、電子線束等產品，廣泛應用于汽車電器、電訊、電器等領域。公司本著質量為本、誠信至上的宗旨，竭誠為新老客戶優質的產品和服務
此規格適用于“汽車排插連接器”系列
this spec is applicable for “car line connector”series.
二、額定值:dc 34v 2a
norminal rating: dc 34v 2a
三、構造（struction）
3.1形狀,尺寸根據圖紙確定（ form, dimension according to the drawing）.
3.2各部分無生銹、裂痕、電鍍不良現象（without rust and oxydation、crack、defective electric plating in all parts）
3.3適應基板厚度（applicble pc board thickness）:1.6mm
四、溫度范圍（temperature range）:-25°c~85°c;
五、材質（ material）
5.1塑膠:pbt plastic （part: pbt）
5.2端子:磷青銅、鈹銅（terminal:be-bronze、phosphor-bronze）;
六、電氣性能（electrical characteristics）
no | 測試項目 test item | 試驗方法及條件 (test condition & method) | 規格standard
|
6.1 | 接觸阻抗contact impedance | 公座和母座導體之間的接觸電阻(measured the resistance of mated pin header )
| 30毫歐以下 (below 30mω) |
6.2 | 絕緣阻抗insulation impedance | 在端子之間和端子與殼之間加dc500v條件下持續1分鐘測量among terminals or between terminal and shell, under condition of dc500v ,last 1min to test | 1000兆歐以上 （ above100mω） |
6.3 | 耐電壓disruptive test | 在端子之間和端子與殼之間加ac 500v(50h或60h)條件下持續1分鐘測量among terminals or between terminals and shell, under condition of ac 500v(50h or 60h),last 1min to test | 無擊穿現象出現 （ without disruptive ） |
七、機械性能（ mechancial character）
no | 測試項目 test item | 試驗方法及條件 (test condition & method) | 規格standard
|
7.1 | 插入力與拔出力度insert and pull out | 用配套插頭插入插座再從中拔出;測量插入和拔出的作用力make the the force of insert the socket and pullout | 插入力度:0.7kgfmax insert force: 0.7kgf max 拔出力度:0.3kgf-2.6kgf pullout force : 0.3kgf to 2.6 kgf |
7.2 | 端子強度 terminal strength | 順端子彈力方向施加500g力條件下持續10秒 add 0.5kgf along the terminal spring , last 10 seconds | 未有裂紋與失去彈性 wiouth fault trace, still with elastic sensation |
八、環境試驗(environmental performance)
no | 測試項目 test item | 試驗方法及條件 (test condition & method) | 規格standard
|
8.1 | 耐高溫試驗 hight temperature resistance test | 在環境中放96小時,再放在正常環境中30分鐘后進行測試test after lasting 96hours under 90±2°c,and then staying 30mins under normal environment |
|
8.2 | 耐低溫試驗 low temperature resistance test | 在-20±3°c環境中放96小時,再放在正常環境中30分鐘后進行測試test after lasting 96hours under -20±3°c,and then staying 30mins under normal environment | |
8.3 | 鹽霧試驗salt spray test | 把試驗樣品從試驗箱懸掛起來,采用濃度為(5±0.1)%(質量百分比)的氯化納溶液連續霧化16小時,試驗后用流動的蒸溜水輕輕洗去表面沉積物,在常溫條件下恢復1-2小時hang up the sample for 16hours in the test box of (5±0.1)%(mass percent) nacl solution, after that flush away the surfacial deposit lightly with running distilled water; finally, under normal environment, make it lay 1-2 hours | 外觀無損傷 (五金件應無露出底金屬的嚴重銹蝕,使用預定好的型材,其落料而允許有不影響其性能的輕微腐蝕) the sample apperance surface is well, non-corroded.(the inside metal of the metal part isn’t badly corroded, slight corrode is possible ,but it doesn’t influence the character. |
九、其它試驗(other characteristic)
no | 測試項目 test item | 試驗方法及條件 (test condition & method) | 規格standard
|
9.1 | 可焊性試驗 weldability test | 將端子頂部浸入焊錫池2mm深;溫度270±5°c;時間2±0.5秒 infusion the terminal top into soldering acid 2m deep; termperature: 270±5°c ;duraton: 2±0.5 seconds | 浸入部分90%以上表面被錫覆蓋 90% of the part infused is plating by tin |
9.2 | 壽命試驗life testing | 在無負荷條件下以每分鐘15-18次的速度操作10000次 under unloaded condition ,working ten thousand times at the speed of 15-18 times per min |
|
一、此規格適用于“汽車排插”系列
this spec is applicable for “car line connector”series.
二、額定值:dc 34v 2a
norminal rating: dc 34v 2a
三、構造（struction）
3.1形狀,尺寸根據圖紙確定（ form, dimension according to the drawing）.
3.2各部分無生銹、裂痕、電鍍不良現象（without rust and oxydation、crack、defective electric plating in all parts）
3.3適應基板厚度（applicble pc board thickness）:1.6mm
四、溫度范圍（temperature range）:-25°c~85°c;
五、材質（ material）
5.1塑膠:pbt plastic （part: pbt）
5.2端子:磷青銅、鈹銅（terminal:be-bronze、phosphor-bronze）;
六、電氣性能（electrical characteristics）
no | 測試項目 test item | 試驗方法及條件 (test condition & method) | 規格standard
|
6.1 | 接觸阻抗contact impedance | 公座和母座導體之間的接觸電阻(measured the resistance of mated pin header )
| 30毫歐以下 (below 30mω) |
6.2 | 絕緣阻抗insulation impedance | 在端子之間和端子與殼之間加dc500v條件下持續1分鐘測量among terminals or between terminal and shell, under condition of dc500v ,last 1min to test | 1000兆歐以上 （ above100mω） |
6.3 | 耐電壓disruptive test | 在端子之間和端子與殼之間加ac 500v(50h或60h)條件下持續1分鐘測量among terminals or between terminals and shell, under condition of ac 500v(50h or 60h),last 1min to test | 無擊穿現象出現 （ without disruptive ） |
七、機械性能（ mechancial character）
no | 測試項目 test item | 試驗方法及條件 (test condition & method) | 規格standard
|
7.1 | 插入力與拔出力度insert and pull out | 用配套插頭插入插座再從中拔出;測量插入和拔出的作用力make the the force of insert the socket and pullout | 插入力度:0.7kgfmax insert force: 0.7kgf max 拔出力度:0.3kgf-2.6kgf pullout force : 0.3kgf to 2.6 kgf |
7.2 | 端子強度 terminal strength | 順端子彈力方向施加500g力條件下持續10秒 add 0.5kgf along the terminal spring , last 10 seconds | 未有裂紋與失去彈性 wiouth fault trace, still with elastic sensation |
八、環境試驗(environmental performance)
no | 測試項目 test item | 試驗方法及條件 (test condition & method) | 規格standard
|
8.1 | 耐高溫試驗 hight temperature resistance test | 在環境中放96小時,再放在正常環境中30分鐘后進行測試test after lasting 96hours under 90±2°c,and then staying 30mins under normal environment |
|
8.2 | 耐低溫試驗 low temperature resistance test | 在-20±3°c環境中放96小時,再放在正常環境中30分鐘后進行測試test after lasting 96hours under -20±3°c,and then staying 30mins under normal environment | |
8.3 | 鹽霧試驗salt spray test | 把試驗樣品從試驗箱懸掛起來,采用濃度為(5±0.1)%(質量百分比)的氯化納溶液連續霧化16小時,試驗后用流動的蒸溜水輕輕洗去表面沉積物,在常溫條件下恢復1-2小時hang up the sample for 16hours in the test box of (5±0.1)%(mass percent) nacl solution, after that flush away the surfacial deposit lightly with running distilled water; finally, under normal environment, make it lay 1-2 hours | 外觀無損傷 (五金件應無露出底金屬的嚴重銹蝕,使用預定好的型材,其落料而允許有不影響其性能的輕微腐蝕) the sample apperance surface is well, non-corroded.(the inside metal of the metal part isn’t badly corroded, slight corrode is possible ,but it doesn’t influence the character. |
九、其它試驗(other characteristic)
no | 測試項目 test item | 試驗方法及條件 (test condition & method) | 規格standard
|
9.1 | 可焊性試驗 weldability test | 將端子頂部浸入焊錫池2mm深;溫度270±5°c;時間2±0.5秒 infusion the terminal top into soldering acid 2m deep; termperature: 270±5°c ;duraton: 2±0.5 seconds | 浸入部分90%以上表面被錫覆蓋 90% of the part infused is plating by tin |
9.2 | 壽命試驗life testing | 在無負荷條件下以每分鐘15-18次的速度操作10000次 under unloaded condition ,working ten thousand times at the speed of 15-18 times per min |
|