- 您現在的位置：買賣IC網 > PDF目錄2067 > DS2450S+T&R (Maxim Integrated Products)IC CONVERTER A/D QUAD 1-W 8-SOIC PDF資料下載
參數資料
| 型號： | DS2450S+T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 22/25頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CONVERTER A/D QUAD 1-W 8-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 產品變化通告： | Product Discontinuation 27/Jul/12 |
| 標準包裝： | 2,000 |
| 位數： | 16 |
| 采樣率（每秒）： | 1k |
| 數據接口： | 串行 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 2.5mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 4 個單端，單極 |
DS2450
6 of 24
MEMORY MAP PAGE 2, ALARM SETTINGS
Figure 5c
Address
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
10
MSBL-A
A
LSBL-A
11
MSBH-A
A
LSBH-A
12
MSBL-B
B
LSBL-B
13
MSBH-B
B
LSBH-B
14
MSBL-C
C
LSBL-C
15
MSBH-C
C
LSBH-C
16
MSBL-D
D
LSBL-D
17
MSBH-D
D
LSBH-D
The registers for the alarm threshold voltages of each channel are located in memory page 2 with the low
threshold being at the lower address (Figure 5c). The power-on default thresholds are 00h for low alarm
and FFh for high alarm. The alarm settings are always eight bits. For a resolution higher or equal to
eight bits the alarm flag will be set if the eight most significant bits of the conversion result yield a
number higher than stored in the high alarm register (AFH) or lower than stored in the low alarm register
(AFL). For a resolution lower than eight bits the least significant bits of the alarm registers are ignored.
MEMORY MAP PAGE 3, Factory Calibration, VCC Control Byte
Figure 5d
Address
18
Factory Calibration (do not change)
19
Factory Calibration (do not change)
1A
Factory Calibration (do not change)
1B
Factory Calibration (do not change)
1C
Set to 40 hex if VCC powered
1D
Factory Calibration (do not change)
1E
Factory Calibration (do not change)
1F
Factory Calibration (do not change)
There is a fourth memory page in the address range of 18 to 1F used during calibration at the factory.
This memory page is accessible to the user through the Read Memory and Write Memory commands.
Changing the data of this page arbitrarily will de-calibrate the A/D converter or make the device
nonfunctional until it undergoes a power-on reset. If the device is VCC powered the analog circuitry
must be kept permanently active by writing a value of 40 hex to memory address 1C after power-up.
This also eliminates the offset time otherwise needed with each CONVERT command. See the
description of the CONVERT command for details.
FUNCTION COMMANDS
The Function Command Flow Chart (Figure 6) describes the protocols necessary for accessing the device
registers. Since the memory map of the DS2450 is small compared to the 16-bit addressing capabilities
the 11 most significant bits of the address will be forced to 0 before they enter the CRC-generator. The
communication between master and DS2450 takes place either at regular speed (default, OD = 0) or at
Overdrive Speed (OD = 1). If not explicitly set into Overdrive mode the device assumes regular speed.
相關PDF資料 |
PDF描述 |
|---|---|
| DS3508E+ | IC GAMMA BUFFER 8CH 20-TSSOP |
| DS3510T+ | IC I2C GAMMA/VCOM BUFF 48-TQFN |
| DS3514T+T&R | IC I2C GAMMA/VCOM BUFF 48-TQFN |
| EL1881CS-T13 | IC VIDEO SYNC SEPARATOR 8-SOIC |
| EL1883IS-T13 | IC VID SYNC SEPARATOR HORZ 8SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS245CEDX | 制造商:CUTLER HAMMER/EATON 功能描述: 制造商:Eaton Corporation 功能描述: 制造商:Eaton Corporation 功能描述:RWD |
| DS246 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| DS2460 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:SHA-1 Coprocessor with EEPROM |
| DS2460+ | 制造商:Maxim Integrated Products 功能描述: |
| DS2460S | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:SHA-1 Coprocessor with EEPROM |
發(fā)布緊急采購，3分鐘左右您將得到回復。