- 您現在的位置：買賣IC網 > PDF目錄97868 > DS2404S-001 (MAXIM INTEGRATED PRODUCTS INC) 0 TIMER(S), REAL TIME CLOCK, PDSO16 PDF資料下載
參數資料
| 型號： | DS2404S-001 |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | Timer or RTC |
| 英文描述： | 0 TIMER(S), REAL TIME CLOCK, PDSO16 |
| 封裝： | 0.300 INCH, SOIC-16 |
| 文件頁數： | 9/31頁 |
| 文件大?。?/td> | 1591K |
| 代理商： | DS2404S-001 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
DS2404
17 of 29
1-WIRE SIGNALING
The DS2404 requires strict protocols to ensure data integrity. The protocol consists of five types of
signaling on one line: Reset Sequence with reset pulse and presence pulse, write 0, write 1, Read Data
and interrupt pulse. All these signals except presence pulse and interrupt pulse are initiated by the bus
master.
The initialization sequence required to begin any communication with the DS2404 is shown in Figure 10.
A reset pulse followed by a presence pulse indicates the DS2404 is ready to send or receive data given the
correct ROM command and memory function command.
The bus master transmits (TX ) a reset pulse (tRSTL , minimum of 480 μs). The bus master then releases the
line and goes into receive mode (RX ). The 1-Wire bus is pulled to a high state via the pull-up resistor.
After detecting the rising edge on the date line, the DS2404 waits (tPDH , 15-60 μs) and then transmits the
presence pulse (tPDL, 60 - 240 μs). There are special conditions if interrupts are enabled where the bus
master must check the state of the 1-Wire bus after being in the RX mode for 480 μs. These conditions
will be discussed in the “Interrupt” section.
READ/WRITE TIME SLOTS
The definitions of write and read time slots are illustrated in Figure 11. All time slots are initiated by the
master driving the data line low. The falling edge of the data line synchronizes the DS2404 to the master
by triggering a delay circuit in the DS2404. During write time slots, the delay circuit determines when the
DS2404 will sample the data line. For a read data time slot, if a “0” is to be transmitted, the delay circuit
determines how long the DS2404 will hold the data line low overriding the 1 generated by the master. If
the data bit is a “1”, the device will leave the read data time slot unchanged.
INITIALIZATION PROCEDURE “RESET AND PRESENCE PULSES” Figure 10
480
μs ≤ tRSTL < ∞ *
480
μs ≤ tRSTH < ∞ (includes recovery time)
15
μs ≤ tPDH < 60 μs
60
μs ≤ tPDL < 240 μs
In order not to mask interrupt signaling by other devices on the 1-Wire bus, tRSTL + tR should always
be less than 960
μs.
RESISTOR
MASTER
DS2404
相關PDF資料 |
PDF描述 |
|---|---|
| DS2404B | 0 TIMER(S), REAL TIME CLOCK, PDSO16 |
| DS2404 | 0 TIMER(S), REAL TIME CLOCK, PDIP16 |
| DS2405P | SPECIALTY MEMORY CIRCUIT, PDSO6 |
| DS2405 | SPECIALTY MEMORY CIRCUIT, PBCY3 |
| DS2405Z | SPECIALTY MEMORY CIRCUIT, PDSO4 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2404S-001/T&R | 制造商:Maxim Integrated Products 功能描述:ECONORAM/TIME, SOIC16-TRL (GENERIC) - Tape and Reel |
| DS2404S-001+ | 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK SERL 512BYTE 16SOIC - Rail/Tube |
| DS2404S-001+T&R | 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK SERL 512BYTE 16SOIC - Tape and Reel |
| DS2404S-C01 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Peripheral IC |
| DS2405 | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發布緊急采購，3分鐘左右您將得到回復。