參數資料
型號: CY28346OXC
廠商: Silicon Laboratories Inc
文件頁數: 13/19頁
文件大?。?/td> 0K
描述: IC CLOCK DIFF OUT CK408 56SSOP
標準包裝: 26
類型: *
PLL:
輸入: 晶體
輸出: 時鐘
電路數: 1
比率 - 輸入:輸出: 1:19
差分 - 輸入:輸出: 無/是
頻率 - 最大: 200MHz
除法器/乘法器: 是/無
電源電壓: 3.135 V ~ 3.465 V
工作溫度: 0°C ~ 70°C
安裝類型: *
封裝/外殼: *
供應商設備封裝: *
包裝: *
其它名稱: SLCY28346OXC
CY28346
........................Document #: 38-07331 Rev. *C Page 3 of 19
Two-Wire SMBus Control Interface
The two-wire control interface implements a Read/Write slave
only interface according to SMBus specification.
The device will accept data written to the D2 address and data
may read back from address D3. It will not respond to any
other addresses, and previously set control registers are
retained as long as power in maintained on the device.
Serial Control Registers
Following the acknowledge of the Address Byte, two additional
bytes must be sent:
1. “Command code” byte
2. “Byte count” byte.
Although the data (bits) in the command is considered “don’t
care,” it must be sent and will be acknowledged. After the
Command Code and the Byte Count have been acknowl-
edged, the sequence (Byte 0, Byte 1, and Byte 2) described
below will be valid and acknowledged.
Byte 0: CPU Clock Register[2,3]
Bit
@Pup
Pin#
Description
7
0
Spread Spectrum Enable. 0 = Spread Off, 1 = Spread On
This is a Read and Write control bit.
6
0
CPU Clock Power-down Mode Select. 0 = Drive CPUT(0:2) to 4 or 6 IREF and drive
CPUC(0:2) LOW when PD# is asserted LOW. 1 = Tri-state all CPU outputs. This is only
applicable when PD# is LOW. It is not applicable to CPU_STP#.
5
0
35
3V66_1/VCH Frequency Select, 0 = 66M selected, 1 = 48M selected
This is a Read and Write control bit.
4
Pin 53
44,45,48,49,5
1,52
CPU_STP#. Reflects the current value of the external CPU_STP# (pin 53) This bit is
Read-only.
3
Pin 34
10,11,12,13,16
,17,18
Reflects the current value of the internal PCI_STP# function when read. Internally PCI_STP#
is a logical AND function of the internal SMBus register bit and the external PCI_STP# pin.
2
Pin 40
Frequency Select Bit 2. Reflects the value of SEL2 (pin 40). This bit is Read-only.
1
Pin 55
Frequency Select Bit 1. Reflects the value of SEL1 (pin 55). This bit is Read-only.
0
Pin 54
Frequency Select Bit 0. Reflects the value of SEL0 (pin 54). This bit is Read-only.
Byte 1: CPU Clock Register
Bit
@Pup
Pin#
Description
7
Pin 43
43
MULT0 (Pin 43) Value. This bit is Read-only.
6
0
53
CPUT/C(0:2) Output Functionality Control When CPU_STP# is Asserted. 0 = Drive
CPUT(0:2) to 4 or 6 IREF and drive CPUC(0:2) LOW when CPU_STP# asserted LOW.
1 = three-state all CPU outputs. This bit will override Byte0,Bit6 such that even if it is 0,
when PD# goes LOW the CPU outputs will be three-stated.
5
0
44,45
CPU2 Functionality Control When CPU_STP# is Asserted LOW. 1 = Free Running, 0 =
Stopped LOW with CPU_STP# asserted LOW. This is a Read and Write control bit.
4
0
48,49
CPU1 Functionality Control When CPU_STP# is Asserted LOW. 1 = Free Running, 0 =
Stopped LOW with CPU_STP# asserted LOW. This is a Read and Write control bit.
3
0
51,52
CPUT0 Functionality Control When CPU_STP# is Asserted LOW. 1 = Free Running, 0 =
Stopped LOW with CPU_STP# asserted LOW. This is a Read and Write control bit.
2
1
44,45
CPUT/C2 Output Control. 1 = enabled, 0 = disable HIGH and CPUC2 disables LOW. This
is a Read and Write control bit.
1
48,49
CPUT/C1 Output Control. 1 = enabled, 0 = disable HIGH and CPUC1 disables LOW. This
is a Read and Write control bit.
0
1
51,52
CPUT/C0 Output Control. 1 = enabled, 0 = disable HIGH and CPUC0 disables LOW. This
is a Read and Write control bit.
Notes:
2. PU = internal pull-up. PD = internal pull-down. T = tri-level logic input with valid logic voltages of LOW = < 0.8V, T = 1.0 – 1.8V and HIGH = > 2.0V.
3. The “Pin#” column lists the relevant pin number where applicable. The “@Pup” column gives the default state at power-up.
相關PDF資料
PDF描述
CY28346ZI-2 IC CLOCK DIFF OUT CK408 56TSSOP
CY28353OXC-2 IC CLOCK DIFF/DRIVER PLL 28TSSOP
CY28409OXC IC CLOCK CK409GRANTSDALE 56TSSOP
CY28419ZXC IC CLOCK SERV CK419 56TSSOP
CY28508OXC IC CLOCK SSCG 3DIFF PAIR 28SSOP
相關代理商/技術參數
參數描述
CY28346OXCT 功能描述:時鐘合成器/抖動清除器 NB clk for Intel 830M & 845 chipsets RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
CY28346ZC 功能描述:時鐘合成器/抖動清除器 NB clk for Intel 830M & 845 chipsets RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
CY28346ZC-2 制造商:Rochester Electronics LLC 功能描述:FTG FOR INTEL 830M AND 845 CHIPSETS (CK-408) - Bulk
CY28346ZC-2T 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Clock Synthesizer with Differential CPU Outputs
CY28346ZCT 功能描述:時鐘合成器/抖動清除器 NB clk for Intel 830M & 845 chipsets RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel