- 您現在的位置：買賣IC網 > PDF目錄378882 > CMC02 (Toshiba Corporation) For Strobe Discharge Circuit PDF資料下載
參數資料
| 型號： | CMC02 |
| 廠商： | Toshiba Corporation |
| 英文描述： | For Strobe Discharge Circuit |
| 中文描述： | 對于頻閃放電電路 |
| 文件頁數： | 3/5頁 |
| 文件大小： | 263K |
| 代理商： | CMC02 |
CMC02
2006-11-06
3
Handling Precautions
The absolute maximum ratings denote the absolute maximum ratings, which are rated values and must not be
exceeded during operation, even for an instant. The following are the general derating methods we recommend for
designing a circuit using this device.
V
RRM
: We recommend that the worst case voltage, including surge voltage, be no greater than 80% of the absolute
maximum rating of V
RRM
for a DC circuit, and no greater than 50% of that of V
RRM
for an AC circuit.
V
RRM
has a temperature coefficient of 0.1%/
℃
. Be sure to take this temperature coefficient into account
when designing a device for use at low temperature.
I
F
(AV): We recommend that the worst case current be no greater than 80% of the absolute maximum rating of I
F
(AV). Carry out sufficient heat design.
If it is not possible to design a circuit with excellent heat radiation, set
a margin by using an allowable Tamax- I
F
(AV) curve.
This rating applies only to a strobe flash circuit. We recommend that the worst case current be kept within the
absolute maximum rating of I
FRM
. The total number of repetitive currents should not exceed 7000 within the
lifespan of the device.
This rating specifies the non-repetitive peak current in one cycle of a 50 Hz sine wave, condition angle 180°.
Therefore the rating applies only to abnormal operation, which seldom occurs during the lifespan of a device.
For this device, we recommend a
Tj of below 120
℃
under the worst load and heat radiation conditions.
Thermal resistance between junction and ambient fluctuates depending on the mounting condition of the device.
When using the device, be sure to design the circuit board and soldering land size to match the appropriate thermal
resistance value.
Refer to the Rectifier databook for further information.
相關PDF資料 |
PDF描述 |
|---|---|
| CMF01 | Zener Diode; Application: General; Pd (mW): 400; Vz (V): 9.5 to 9.9; Condition Iz at Vz (mA): 5; C (pF) max: -; Condition VR at C (V):   ESD (kV) min: -; Package: MHD |
| CMF02 | Zener Diode; Application: General; Pd (mW): 400; Vz (V): 9.7 to 10.1; Condition Iz at Vz (mA): 5; C (pF) max: -; Condition VR at C (V):   ESD (kV) min: -; Package: MHD |
| CMF03 | Switching Mode Power Supply Applications |
| CMF04 | Zener Diode; Application: General; Pd (mW): 400; Vz (V): 9.9 to 10.3; Condition Iz at Vz (mA): 5; C (pF) max: -; Condition VR at C (V):   ESD (kV) min: -; Package: MHD |
| CMG02 | Zener Diode; Application: General; Pd (mW): 400; Vz (V): 10.2 to 10.6; Condition Iz at Vz (mA): 5; C (pF) max: -; Condition VR at C (V):   ESD (kV) min: -; Package: MHD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CMC02(TE12L,Q) | 功能描述:整流器 Diode 400V 1A RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel |
| CMC02(TE12L,Q,M) | 功能描述:整流器 400V Vrrm 1.0A IF 1.0V VFM 150A IFRM RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel |
| CMC020C | 制造商:CORNELL DUBILIER ELECTRONICS 功能描述:Cap Ceramic 2pF 500V C0G 0.25pF (6 X 4mm) Radial 6.4mm 125°C |
| CMC030C | 制造商:Cornell Dubilier Electronics 功能描述:Cap Ceramic 3pF 500V C0G 0.25pF (6 X 4mm) Radial 6.4mm 125°C |
| CMC040C | 制造商:Cornell Dubilier Electronics 功能描述:Cap Ceramic 4pF 500V C0G 0.25pF (6 X 4mm) Radial 6.4mm 125°C |
發布緊急采購，3分鐘左右您將得到回復。