- 您現在的位置：買賣IC網 > PDF目錄378882 > CMC01 (Toshiba Corporation) SILICON DIFFUSED TYPE For Strobe Discharge Circuit PDF資料下載
參數資料
| 型號： | CMC01 |
| 廠商： | Toshiba Corporation |
| 英文描述： | SILICON DIFFUSED TYPE For Strobe Discharge Circuit |
| 中文描述： | 硅擴散類型頻閃放電電路 |
| 文件頁數： | 3/5頁 |
| 文件大?。?/td> | 200K |
| 代理商： | CMC01 |
CMC01
2006-11-06
3
Handling Precaution
The absolute maximum ratings denote the absolute maximum ratings, which are rated values and must not be
exceeded during operation, even for an instant. The following are the general derating methods that we recommend
when you design a circuit with a device.
V
RRM
: We recommend that the worst case voltage, including surge voltage, be no greater than 80% of the absolute
maximum rating of V
RRM
for a DC circuit and be no greater than 50% of that of V
RRM
for an AC circuit.
V
RRM
has a temperature coefficient of 0.1%/
℃
. Take this temperature coefficient into account designing a
device at low temperature.
I
F(AV):
We recommend that the worst case current be no greater than 80% of the absolute maximum rating of I
F(AV)
.
Carry out adequate heat design. If you can’t design a circuit with excellent heat radiation, please set the
margin by using an allowable Tamax-I
F (AV)
curve.
This rating is only applied for a strobe flash circuit. We recommend that the worst case current be controlled less
than the absolute maximum rating of I
FRM
. The total number of repetitive currents must be less than 5000 times
within the lifespan of the device.
This rating specifies the non-repetitive peak current in one cycle of a 50-Hz sine wave, condition angle 180.
Therefore, this is only applied for an abnormal operation, which seldom occurs during the lifespan of the device.
We recommend that a device be used at a Tj of below 120
℃
under the worst load and heat radiation conditions.
Thermal resistance between junction and ambient fluctuates depending on the device’s mounting condition. When
using a device, design a circuit board and a soldering land size to match the appropriate thermal resistance value.
Please refer to the Rectifiers databook for further information.
相關PDF資料 |
PDF描述 |
|---|---|
| CMC01_06 | SILICON DIFFUSED TYPE For Strobe Discharge Circuit |
| CMC02 | For Strobe Discharge Circuit |
| CMF01 | Zener Diode; Application: General; Pd (mW): 400; Vz (V): 9.5 to 9.9; Condition Iz at Vz (mA): 5; C (pF) max: -; Condition VR at C (V):   ESD (kV) min: -; Package: MHD |
| CMF02 | Zener Diode; Application: General; Pd (mW): 400; Vz (V): 9.7 to 10.1; Condition Iz at Vz (mA): 5; C (pF) max: -; Condition VR at C (V):   ESD (kV) min: -; Package: MHD |
| CMF03 | Switching Mode Power Supply Applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CMC-01 | 功能描述:固定電感器 Common Mode Choke FOR EMC NAVin NAVout RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm |
| CMC01(TE12L,Q) | 功能描述:整流器 Diode 400V 1A RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel |
| CMC01_06 | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:SILICON DIFFUSED TYPE For Strobe Discharge Circuit |
| CM-C010 | 制造商:Southco 功能描述: |
| CMC-010/104KX50201TF | 制造商:TECATE IND. 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。