- 您現在的位置：買賣IC網 > PDF目錄366551 > AM79C987JC (ADVANCED MICRO DEVICES INC) Hardware Implemented Management Information Base (HIMIB) Device PDF資料下載
參數資料
| 型號： | AM79C987JC |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | 網絡接口 |
| 英文描述： | Hardware Implemented Management Information Base (HIMIB) Device |
| 中文描述： | DATACOM, ETHERNET TRANSCEIVER, PQCC28 |
| 封裝： | PLASTIC, LCC-28 |
| 文件頁數： | 12/30頁 |
| 文件大小： | 183K |
| 代理商： | AM79C987JC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
AMD
P R E L I M I N A R Y
12
Am79C987
DETAILED REGISTER FUNCTIONS
Status Register
The HIMIB Status Register can be accessed at any time
by reading the C Port.
The 8-bit quantity read has the following format:
C Port Read
MSB
LSB
E
I
S
X
X
X
X
X
I Interrupt. This bit reflects the state of the
INT
output
pin. If this bit is set to 1, then this HIMIB device is driv-
ing the
INT
pin. Note that the
INT
pin is an open drain
output and multiple devices may share the same in-
terrupt signal.
E Interface Error. This bit is set if the HIMIB device is
unable to communicate with the IMR+ device. This
bit is reset upon reading this register.
S Source Address Match. This bit is set if the interrupt
is caused by a source address match of the incoming
data packet. This bit remains set until the TP and/or
AUI Source Address Match Status register(s) in the
Port Status registers are read.
X Reserved. The values of reserved bits are
indeterminate.
Repeater, Port Status, Port Control and
Port Attribute Register Access
The bit pattern which must be written to the C Port in or-
der to correctly set the value of the R register to access
each of the registers is described in this section.
Repeater Register Bank
These registers are accessed by writing the bit pattern
0000 0000 to the C Port, i.e., P[4:0] = 0. Content of all
attribute counters are indeterminate upon power up.
Source Address Match Register
P[4:0] = 0, R[4:0] = 10
Byte 0
Byte 1
Byte 2
Byte 3
Byte 4
Byte 5
bit 7
bit 47
bit 0
bit 40
MSB
LSB
D Port Read/Write
This is a read/write register. The 6 bytes are read or writ-
ten in Low byte to High byte order. The sequence is
(re)started once the C Port is programmed for access to
this register. This register may be used to track nodes
within a LAN by reporting the port that received a packet
with a specific Source Address (SA). The Source Ad-
dress field of an incoming packet is always compared
with the 48-bit quantity stored in this register. The initial
value of this register is indeterminate.
A match is indicated by the HIMIB device by setting the
corresponding bit in the TP or AUI Source Address
Match Status register for the receiving port. If the corre-
sponding Source Address Match Interrupt Enable bit is
enabled, then the
INT
output pin is driven LOW. The set
bit(s) in the TP/AUI Source Address Match Status Reg-
isters are cleared when these registers are read.
Note that once a write sequence is started, all 6 bytes
must be written in order to change the contents of this
register.
Total Octets
P[4:0] = 0, R[4:0] = 12
Byte 0
Byte 1
Byte 2
Byte 3
bit 7
bit 31
bit 0
bit 24
MSB
LSB
D Port Read
This is a 4-byte attribute, read only register, whose con-
tents are incremented while the repeater is repeating
packet data. This counter is a truncated divide by 8 of
the total number of bits transmitted by the repeater. The
counter is incremented for non-collision packets with
valid SFD (Start of Frame Delimiter). This attribute in-
crements by same amount for all HIMIB devices con-
nected to the same expansion bus in a repeater.
The 4 bytes in this attribute are sequentially accessed
by reading the D Port, least significant byte first. Note
that once the C Port is programmed for access to this at-
tribute, reading the D Port causes the value of this regis-
ter to be copied to the internal holding register. The data
is then read from the holding register, without affecting
this attribute. This sequence is repeated when the last
byte is read and the D Port is accessed.
相關PDF資料 |
PDF描述 |
|---|---|
| AM79C987JCB | Hardware Implemented Management Information Base (HIMIB) Device |
| AM79C988A | IC,Motor Controller,CMOS,SOP,8PIN |
| AM79C988 | Quad Integrated Ethernet Transceiver (QuIET⑩) |
| Am79C988BJC | Quad Integrated Ethernet Transceiver (QuIET⑩) |
| AM79C989 | Motor Driver IC; Supply Voltage Max:13.2V; Output Current Max:0.5A; Package/Case:8-SOIC; Driver Type:Motor; Leaded Process Compatible:No; Output Current:1.5A; Peak Reflow Compatible (260 C):No; Supply Voltage Min:3.8V |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM79C987JCB | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Hardware Implemented Management Information Base (HIMIB) Device |
| AM79C988 | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Quad Integrated Ethernet Transceiver (QuIET⑩) |
| AM79C988A | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Quad Integrated Ethernet Transceiver (QuIET⑩) |
| AM79C988BJC | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。