- 您現在的位置：買賣IC網 > PDF目錄364551 > 8XC51SL.LOWVOLTAGE8XC51SL (Intel Corp.) KEYBOARD CONTROLLER PDF資料下載
參數資料
| 型號： | 8XC51SL.LOWVOLTAGE8XC51SL |
| 廠商： | Intel Corp. |
| 英文描述： | KEYBOARD CONTROLLER |
| 中文描述： | 鍵盤控制器 |
| 文件頁數： | 45/58頁 |
| 文件大小： | 233K |
| 代理商： | 8XC51SL.LOWVOLTAGE8XC51SL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁當前第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
2003 Oct 30
45
Philips Semiconductors
Product specification
Low power single card reader
TDA8029
When in Power-down or Sleep mode, card extraction or
insertion, overcurrent on V
CC
, or HIGH level on pins RST
or RESET will wake up the chip.
The same occurs in case of a falling edge on RX if bit
ENRX is set, or on INT1_N if bit ENINT1 is set and if
INT1_N is enabled within the controller.
IfonlyINT1_Nshouldwake upthe TDA8029, thenINT1_N
must be enabled in the controller, and ENINT1 only should
be set.
If RX should wake up the TDA8029, then INT1_N must be
enabled in the controller, and ENRX and ENINT1 should
be set.
In case of wake up by RX, then the first received
characters may be lost, depending on the baud rate on the
serial link. (The controller waits for 1536 clock cycles
before leaving Power-down mode).
For more details about the use of these modes, please
refer to the application notes “AN00069”and “AN01005”
8.16
Activation sequence
When the card is inactive, V
CC
, CLK, RST and I/O are
LOW, with low impedance with respect to GNDC. The
DC/DC converter is stopped.
When everything is satisfactory (voltage supply, card
present and no hardware problems), the system controller
may initiate an activation sequence of the card. Figure 12
shows the activation sequence.
After leaving the UART reset mode, and then configuring
the necessary parameters for the UART, it may set the bit
START in register PCR (t
0
). The following sequence will
take place:
The DC/DC converter is started (t
1
)
V
CC
starts rising from 0 to 5 V or 3 V with a controlled
rise time of 0.17 V/
μ
s typically (t
2
)
I/O rises to V
CC
(t
3
), (Integrated 14 k
pull-up to V
CC
)
CLK is sent to the card and RST is enabled (t
4
).
Afteranumberofclockpulsesthatcanbecountedwiththe
time out counter, bit RSTIN may be set by software, then
pin RST rises to V
CC
.
The sequencer is clocked by
1
/
64
f
int
which leads to a time
interval T of 25
μ
s typical. Thus t
1
= 0 to
3
/
64
T,
t
2
= t
1
+
3
/
2
T, t
3
= t
1
+
7
/
2
T, and t
4
= t
1
+ 4T.
handbook, full pagewidth
START
VUP
VCC
I/O
RSTIN
CLK
RST
t0
t2
t3
t4 = tact
ATR
t1
FCE684
Fig.12 Activation sequence.
相關PDF資料 |
PDF描述 |
|---|---|
| 8XC51SLLOWVOLTAGE8XC51SL | KEYBOARD CONTROLLER |
| 8XC52 | 80C51 8-Bit Microcontroller Family (8K ROM,Low Voltage (2.7V-5.5V), Low Power, High Speed (33 MHz) )(80C51 8位微控制器系列產品) |
| 8XC54 | 80C51 8-bit microcontroller family 8K-64K/256-1K OTP/ROM/ROMless, low voltage 2.7V-5.5V), low power, high speed (33 MHz) |
| 8XC58 | 80C51 8-bit microcontroller family 8XC51FA/FB/FC/80C51FA8XC51RA+/RB+/RC+/RD+/80C51RA +8K 4K/256K OTP/ROM/ROMless,low voltage, low power, high speed (33 MHz)(80C51 8位微控制器系列產品) |
| 8XC562 | 80C51 FAMILY DERIVATIVES |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 8XC52 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER |
| 8XC54 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER |
| 8XC54/58 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:(360.35 k) |
| 8XC552 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80C51 FAMILY DERIVATIVES |
| 8XC562 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80C51 FAMILY DERIVATIVES |
發布緊急采購，3分鐘左右您將得到回復。