參數資料
型號: 8XC51FA
廠商: NXP Semiconductors N.V.
英文描述: 8-bit CMOS (low voltage, low power and high speed) microcontroller families
中文描述: 8位CMOS(低電壓,低功耗和高速)微控制器系列
文件頁數: 17/55頁
文件大?。?/td> 361K
代理商: 8XC51FA
Philips Semiconductors
Preliminary specification
8XC52/54/58/80C32
8XC51FA/FB/FC/80C51FA
8XC51RA+/RB+/RC+/RD+/80C51RA+
8-bit CMOS (low voltage, low power
and high speed) microcontroller families
1997 Dec 01
191
OSC
÷
2
C/T2 = 0
C/T2 = 1
TR2
Control
TL2
(8-bits)
TH2
(8-bits)
÷
16
RCAP2L
RCAP2H
EXEN2
Control
EXF2
Timer 2
Interrupt
T2EX Pin
Transition
Detector
T2 Pin
Reload
NOTE: OSC. Freq. is divided by 2, not 12.
÷
2
“0”
“1”
RX Clock
÷
16
TX Clock
“0”
“1”
“0”
“1”
Timer 1
Overflow
Note availability of additional external interrupt.
SMOD
RCLK
TCLK
SU00068
Figure 6. Timer 2 in Baud Rate Generator Mode
Table 5. Timer 2 Generated Commonly Used
Baud Rates
Ba d Rate
Baud Rate
Osc Freq
Timer 2
RCAP2H
RCAP2L
375K
9.6K
2.8K
2.4K
1.2K
300
110
300
110
12MHz
12MHz
12MHz
12MHz
12MHz
12MHz
12MHz
6MHz
6MHz
FF
FF
FF
FF
FE
FB
F2
FD
F9
FF
D9
B2
64
C8
1E
AF
8F
57
Baud Rate Generator Mode
Bits TCLK and/or RCLK in T2CON (Table 3) allow the serial port
transmit and receive baud rates to be derived from either Timer 1 or
Timer 2. When TCLK= 0, Timer 1 is used as the serial port transmit
baud rate generator. When TCLK= 1, Timer 2 is used as the serial
port transmit baud rate generator. RCLK has the same effect for the
serial port receive baud rate. With these two bits, the serial port can
have different receive and transmit baud rates – one generated by
Timer 1, the other by Timer 2.
Figure 6 shows the Timer 2 in baud rate generation mode. The baud
rate generation mode is like the auto-reload mode,in that a rollover
in TH2 causes the Timer 2 registers to be reloaded with the 16-bit
value in registers RCAP2H and RCAP2L, which are preset by
software.
The baud rates in modes 1 and 3 are determined by Timer 2’s
overflow rate given below:
Modes 1 and 3 Baud Rates
Timer 2 Overflow Rate
16
The timer can be configured for either “timer” or “counter” operation.
In many applications, it is configured for “timer” operation (C/T2*=0).
Timer operation is different for Timer 2 when it is being used as a
baud rate generator.
Usually, as a timer it would increment every machine cycle (i.e., 1/12
the oscillator frequency). As a baud rate generator, it increments
every state time (i.e., 1/2 the oscillator frequency). Thus the baud
rate formula is as follows:
Oscillator Frequency
[65536
(RCAP2H,RCAP2L)]]
[32
Modes 1 and 3 Baud Rates =
Where:
RCAP2L taken as a 16-bit unsigned integer.
(RCAP2H, RCAP2L)= The content of RCAP2H and
The Timer 2 as a baud rate generator mode shown in Figure 6, is
valid only if RCLK and/or TCLK = 1 in T2CON register. Note that a
rollover in TH2 does not set TF2, and will not generate an interrupt.
Thus, the Timer 2 interrupt does not have to be disabled when
Timer 2 is in the baud rate generator mode. Also if the EXEN2
(T2 external enable flag) is set, a 1-to-0 transition in T2EX
(Timer/counter 2 trigger input) will set EXF2 (T2 external flag) but
will not cause a reload from (RCAP2H, RCAP2L) to (TH2,TL2).
Therefore when Timer 2 is in use as a baud rate generator, T2EX
can be used as an additional external interrupt, if needed.
相關PDF資料
PDF描述
8XC51FC 8-bit CMOS (low voltage, low power and high speed) microcontroller families
8XC51RD 8-bit CMOS (low voltage, low power and high speed) microcontroller families
8XC80C32 8-bit CMOS (low voltage, low power and high speed) microcontroller families
8XC51FB Low power single card reader
8XC51 CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
相關代理商/技術參數
參數描述
8XC51FA/FB/FC/80C51FA 制造商:未知廠家 制造商全稱:未知廠家 功能描述:(360.35 k)
8XC51FB 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Low power single card reader
8XC51FC 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit CMOS (low voltage, low power and high speed) microcontroller families
8XC51FX 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLERS
8XC51GB 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER