- 您現在的位置：買賣IC網 > PDF目錄364551 > 8XC51 (Intel Corp.) CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | 8XC51 |
| 廠商： | Intel Corp. |
| 英文描述： | CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER |
| 中文描述： | CHMOS單片8位微控制器 |
| 文件頁數： | 39/58頁 |
| 文件大?。?/td> | 233K |
| 代理商： | 8XC51 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁當前第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
2003 Oct 30
39
Philips Semiconductors
Product specification
Low power single card reader
TDA8029
8.10.3.4
UART Configuration Register 1 (UCR1)
This register is used for setting the parameters of the ISO UART.
Table 61
UART configuration register 1, address 6h, read and write
Table 62
Description of register bits
8.10.3.5
Clock Configuration Register (CCR)
This register defines the clock to the card and the clock to the ISO UART. Note that if bit CKU in the prescaler register
of the selected card (register UCR2) is set, then the ISO UART is clocked at twice the frequency to the card, which allows
to reach baud rates not foreseen in ISO 7816 norm.
Table 63
Clock configuration register, address 1h, read and write
BIT
7
6
5
4
3
2
1
0
Symbol
Reset value
FIP
0
FC
0
PROT
0
T/R
0
LCT
0
SS
0
CONV
0
BIT
SYMBOL
DESCRIPTION
7
6
FIP
Not used.
Force Inverse Parity.
If FIP = 1, then the UART will NAK a correct received character,
and will transmit characters with wrong parity bit.
Test bit.
FC must be left to logic 0.
Protocol.
If PROT = 1, then protocol type is asynchronous T = 1; if PROT = 0, the
protocol is T = 0.
Transmit/Receive.
This bit is set by software for transmission mode. A change from
logic 0 to logic 1 will set bit TBE in register USR. T/R is automatically reset by hardware
if LCT has been used before transmitting the last character.
Last Character to Transmit.
This bit is set by software before writing the last character
to be transmitted in register UTR. It allows automatic change to reception mode. It is
reset by hardware at the end of a successful transmission. When LCT is being reset, the
bit T/R is also reset and the ISO 7816 UART is ready for receiving a character.
Start Session.
This bit is set by software before ATR for automatic convention detection
and early answer detection. It is automatically reset by hardware at 10.5 ETU after
reception of the initial character.
Convention.
This bit is set if the convention is direct. Bit CONV is either automatically
written by hardware according to the convention detected during ATR, or by software if
bit AUTOCONV in register UCR2 is set.
5
4
FC
PROT
3
T/R
2
LCT
1
SS
0
CONV
BIT
7
6
5
4
3
2
1
0
Symbol
Reset value
SHL
0
CST
0
SC
0
AC2
0
AC1
0
AC0
0
相關PDF資料 |
PDF描述 |
|---|---|
| 8XC51GB-1 | CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER |
| 8XC51SL.LOWVOLTAGE8XC51SL | KEYBOARD CONTROLLER |
| 8XC51SLLOWVOLTAGE8XC51SL | KEYBOARD CONTROLLER |
| 8XC52 | 80C51 8-Bit Microcontroller Family (8K ROM,Low Voltage (2.7V-5.5V), Low Power, High Speed (33 MHz) )(80C51 8位微控制器系列產品) |
| 8XC54 | 80C51 8-bit microcontroller family 8K-64K/256-1K OTP/ROM/ROMless, low voltage 2.7V-5.5V), low power, high speed (33 MHz) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 8XC51FA | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit CMOS (low voltage, low power and high speed) microcontroller families |
| 8XC51FA/FB/FC/80C51FA | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:(360.35 k) |
| 8XC51FB | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Low power single card reader |
| 8XC51FC | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit CMOS (low voltage, low power and high speed) microcontroller families |
| 8XC51FX | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLERS |
發布緊急采購，3分鐘左右您將得到回復。