- 您現在的位置：買賣IC網 > PDF目錄364551 > 8XC51 (Intel Corp.) CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | 8XC51 |
| 廠商： | Intel Corp. |
| 英文描述： | CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER |
| 中文描述： | CHMOS單片8位微控制器 |
| 文件頁數： | 19/58頁 |
| 文件大?。?/td> | 233K |
| 代理商： | 8XC51 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
2003 Oct 30
19
Philips Semiconductors
Product specification
Low power single card reader
TDA8029
Table 13
Description of register bits
Table 14
Enhanced UART modes
BIT
SYMBOL
DESCRIPTION
7
SM0/FE
The function of this bit is determined by SMOD0, bit 6 of register PCON. If SMOD0 is set
then this bit functions as FE. This bit functions as SM0 when SMOD0 is reset. When
used as FE, this bit can only be cleared by software.
SM0: Serial port mode bit 0.
See Table 14.
FE: Framing Error bit.
This bit is set by the receiver when an invalid stop bit is
detected; see Fig.6. The FE bit is not cleared by valid frames but should be cleared by
software. The SMOD0 bit in register PCON must be set to enable access to FE.
Serial port mode bit 1.
See Table 14.
Serial port mode bit 2.
Enables the automatic address recognition feature in modes
2 or 3. If SM2 = 1, bit Rl will not be set unless the received 9th data bit (RB8) is logic 1;
indicating an address and the received byte is a given or broadcast address. In mode 1,
if SM2 = 1 then Rl will not be activated unless a valid stop bit was received, and the
received byte is a given or broadcast address. In mode 0, SM2 should be logic 0.
Enables serial reception.
Set by software to enable reception. Cleared by software to
disable reception.
The 9th data bit transmitted in modes 2 and 3.
Set or cleared by software as desired.
In mode 0, TB8 is not used.
The 9th data bit received in modes 2 and 3.
In mode 1, if SM2 = 0, RB8 is the stop bit
that was received. In mode 0, RB8 is not used.
Transmit interrupt flag.
Set by hardware at the end of the 8th bit time in mode 0, or at
the beginning of the stop bit in the other modes, in any serial transmission. Must be
cleared by software.
Receive interrupt flag.
Set by hardware at the end of the 8th bit time in mode 0, or
halfway through the stop bit time in the other modes, in any serial reception (except if
SM2 = 1, as described for SM2). Must be cleared by software.
6
5
SM1
SM2
4
REN
3
TB8
2
RB8
1
Tl
0
Rl
SM0
SM1
MODE
DESCRIPTION
BAUD RATE
0
0
1
1
0
1
0
1
0
1
2
3
shift register
8-bit UART
9-bit UART
9-bit UART
1
/
12
f
XTAL1
variable
1
/
32
or
1
/
64
f
XTAL1
variable
8.3.2
A
UTOMATIC ADDRESS RECOGNITION
Automatic address recognition is a feature which allows
the UART to recognize certain addresses in the serial bit
stream by using hardware to make the comparisons. This
feature saves a great deal of software overhead by
eliminating the need for the software to examine every
serialaddress whichpasses bythe serialport.This feature
is enabled by setting the SM2 bit in register SCON. In the
9-bit UART modes (modes 2 and 3), the Receive Interrupt
flag (RI) will be automatically set when the received byte
contains either the ‘given’ address or the ‘broadcast’
address. The 9-bit mode requires that the 9th information
bitisalogic 1toindicatethatthereceivedinformationisan
address and not data. Figure 7 gives a summary.
The 8-bit mode is called mode 1. In this mode the RI flag
will be set if SM2 is enabled and the information received
has a valid stop bit following the 8 address bits and the
information is either a given or a broadcast address.
Mode 0 is the Shift Register mode and SM2 is ignored.
Using the automatic address recognition feature allows a
master to selectively communicate with one or more
slaves by invoking the given slave address or addresses.
All of the slaves may be contacted by using the broadcast
相關PDF資料 |
PDF描述 |
|---|---|
| 8XC51GB-1 | CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER |
| 8XC51SL.LOWVOLTAGE8XC51SL | KEYBOARD CONTROLLER |
| 8XC51SLLOWVOLTAGE8XC51SL | KEYBOARD CONTROLLER |
| 8XC52 | 80C51 8-Bit Microcontroller Family (8K ROM,Low Voltage (2.7V-5.5V), Low Power, High Speed (33 MHz) )(80C51 8位微控制器系列產品) |
| 8XC54 | 80C51 8-bit microcontroller family 8K-64K/256-1K OTP/ROM/ROMless, low voltage 2.7V-5.5V), low power, high speed (33 MHz) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 8XC51FA | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit CMOS (low voltage, low power and high speed) microcontroller families |
| 8XC51FA/FB/FC/80C51FA | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:(360.35 k) |
| 8XC51FB | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Low power single card reader |
| 8XC51FC | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit CMOS (low voltage, low power and high speed) microcontroller families |
| 8XC51FX | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLERS |
發布緊急采購，3分鐘左右您將得到回復。